- 您現在的位置：買賣IC網 > PDF目錄98013 > MCZ33781EK (FREESCALE SEMICONDUCTOR INC) SPECIALTY MICROPROCESSOR CIRCUIT, PDSO32 PDF資料下載
參數資料
| 型號： | MCZ33781EK |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PDSO32 |
| 封裝： | 0.65 MM, LEAD FREE, SOIC-32 |
| 文件頁數： | 19/44頁 |
| 文件大小： | 940K |
| 代理商： | MCZ33781EK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Analog Integrated Circuit Device Data
26
Freescale Semiconductor
33781
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
CRC GENERATION /CHECKING
Whenever a message is sent on the DBUS, a 0- to 8-bit
CRC value is computed and serially sent as the next n bits
after the LSB of the data. The CRC length, polynomial, and
initial seed are determined by the CRCLEN[3:0],
CRCPOLY[7:0], and CRCSEED[7:0] control register fields.
The message, including the CRC bits, is passed along to a
remote peripheral, which computes a separate CRC value as
the message data is received. If this computed and CRC
does not agree with the CRC value received in the message,
the peripheral device considers the message invalid.
Messages received include a 0- to 8-bit CRC value, which
was computed in the peripheral device that is responding. As
the message is received, a separate 0- to 8-bit CRC value is
computed and is compared with the CRC value in the
received message. If these values do not agree, the message
is considered invalid and the ER status bit in the associate
DnRnSTAT register is set at the end of the message along
with the RNE bit.
When no remote peripheral responds to a message, the
data pattern received will be all zeros with a CRC value of 0,
which may be detected as a CRC error depending on the
values of CRCLEN[3:0], CRCPOLY[7:0], and
CRCSEED[7:0].
CRC COMPUTATION
The CRC algorithm uses a programmable initialization
value, or seed of CRCSEED[7:0], and a programmable
polynomial of CRCPOLY[7:0]. Figure 21 is a VHDL
description of the CRC algorithm for the DBUS standard 4-bit
CRC, with its initial value of 1010. A seed value is chosen so
that a zero data value will generate a CRC value of 1010. A
block diagram of the default CRC calculation is shown in
Figure 21. CRC Algorithm
Figure 22. Default CRC Block Diagram
MESSAGE SIZE SPECIAL CASES
The response to any 8- to 15-bit message is expected to
be another 8- to 15-bit message, and the response to any
16-bit message is expected to be another 16-bit message.
This gives rise to some special cases when there is a
transition from one message size to a different message size.
Some messages must be long words (16 bits of data), and
others can be short words (8 to 15 bits of data).
The following are examples where the word is a standard
DSI formatted short word (8 bits of data and 4 bits of CRC).
Example 1: If the previous message was a short word and
the current message is a long word, the response message
(which is also a short word) finishes before the current
message frame, and the CRC bits look like data bits in the
long word format. Since the CRC validation of this short word
message response is not reliable, this short word response
should not be used.
Example 2: If the previous message was a long word and
the current message is a short word, the response message
(which is also a long word) cannot finish before the current
message frame. Bits three to zero of the data and the CRC
bits are lost. Data bits seven to four of the 16-bit response
--------------------------------------------------------------------------
-- Calculates the 4-bit CRC (x^4 + 1) serially for 8 to 16 bits of data.
--------------------------------------------------------------------------
constant CRCPoly: std_logic_vector: = “0001”; -- x^4 +1
constant InitCrc: std_logic_vector: = “1010”;
procedure SerialCalculateCRC4(CRC: input std_logic_vector;Data: in std_logic) is vari-
able Xor1: std_logic;
begin
Xor1: = CRC(3) xor Data;
if Xor1 = ‘1’ then
CRC: = CRC xor CRCPoly
end if;
end SerialCalculateCRC4;
T
C3
T
C2
T
C1
T
C0
Input Data
1X4
0X3
0X2
0X1
+X0
= X4+1
++
+
相關PDF資料 |
PDF描述 |
|---|---|
| MD1802FH | 10 A, 700 V, NPN, Si, POWER TRANSISTOR, TO-220AB |
| MD1802FX | 10 A, 700 V, NPN, Si, POWER TRANSISTOR |
| MD1803DFH | 10 A, 700 V, NPN, Si, POWER TRANSISTOR, TO-220AB |
| MD2001FX | 12 A, 700 V, NPN, Si, POWER TRANSISTOR |
| MD2103DFX | 6 A, 700 V, NPN, Si, POWER TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33781EKR2 | 功能描述:輸入/輸出控制器接口集成電路 DBUS2 MASTER STND RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MCZ33784EF | 功能描述:加速計 - 板上安裝 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| MCZ33784EF/R2- | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:DSI 2.02 Sensor Interface |
| MCZ33784EFR2 | 功能描述:加速計 - 板上安裝 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| MCZ33789AE | 功能描述:網絡控制器與處理器 IC Airbag ASSP RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。