參數資料
型號： MCZ33800EK
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Engine Control Integrated Circuit
中文描述： 發動機控制集成電路
文件頁數： 21/39頁
文件大?。?/td> 461K
代理商： MCZ33800EK
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
33800
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Off State Open Load Detect
On State Short Circuit Detect
Programmable Drain Threshold and Timer for Short Fault
Detection
Load Resistance Measurement
Each pre-driver is capable of detecting an open load in the
off state and shorted load in the on state. All faults are
reported through SPI communication. For open load
detection, a resistor is placed between the drain sense pin
and source sense pin of the IC. An open load fault is reported
when the drain voltage is less than the 2.5V threshold. A
shorted load fault is reported when the drain voltage is
greater than the programmed threshold voltage.
Programming of the drain short fault threshold voltage is
done through SPI commands provided in
Table 7
.
Bits 6 through 9 are used to perform the load resistance
measurement function as described in the Gate Drive On/Off
Command section below.
GATE DRIVE ON/OFF COMMAND
The GD ON/OFF Command provides control bits for two
functions:
On/Off control of the GDx outputs.
Load Resistance measurement function.
On/Off control bit 0 through bit 5 control gate drive outputs
GD1 through GD6 respectively. Setting the bit to logic1 will
enable the gate drive to the external MOSFET. Setting the bit
to logic 0 will actively pull the gate to ground.
GD ON/OFF Command bits 6 through 9 control the load
measurement feature. The gate drive pre-drivers are
selected in matched pairs. Selecting a load resistance
measurement disables a specified output pair and performs
the resistance measurement using the defined pair. All other
outputs will operate as programmed. Resistance is measured
by passing a known current through the load and by
measuring the voltage across it. The resistor placed on the
REXT pin determines the current through the load during
measurement. The voltage output on the LRFDBK pin is the
differential load voltage with the defined current through it.
From the two parameters, the load resistance may be
calculated.
Table 6
illustrates the load diagnostic multiplex
function.
PWM PIN ENABLE COMMAND
The PWM Pin Enable Command provides control bits for
two functions:
Enable or Disable of PWM input pins.
Enable or Disable of the internal PWM controller for GD1
through GD6.
PWM pin Enable bit 0 through bit 5 enable or disable the
PWM1 through PWM6 input pins respectively. A logic 0 in the
SPI word will enable the PWM input pin, while logic 1 in the
SPI word will disable the PWM input pin. Default state is with
the PWM input pin enabled. With the PWM input pin disabled,
the AND/OR function is also disabled and control is achieved
through the Gate Drive ON/OFF command or the internal
PWM controller.
AND /OR COMMAND
The AND/OR Command provides control bits for two
functions:
Determines AND/OR relation between ON/OFF SPI bit
and PWM input pin.
Enable or Disable of the internal PWM controller for G1
through GD6.
The AND OR command describes the condition by which
the PWM input pin controls the output driver. A logic[0] in the
AND / OR register will OR the PWM input pin with the
respective bit in the ON/OFF register. Likewise, a logic[1] in
Table 6. Load Resistance Measurement Select
Bits 9876
MUX Select
0000
Normal Operation
0001
V
DSNS1
to R
EXT
, V
DSNS2
to Diff-Amp +
0010
V
DSNS2
to R
EXT
, V
DSNS1
to Diff-Amp +
0011
V
DSNS3
to R
EXT
, V
DSNS4
to Diff-Amp +
0100
V
DSNS4
to R
EXT
, V
DSNS3
to Diff-Amp +
0101
V
DSNS5
to R
EXT
, V
DSNS6
to Diff-Amp +
0110
V
DSNS6
to R
EXT
, V
DSNS5
to Diff-Amp +
0111
Normal Operation
1000
Normal Operation
1001
Normal Operation
1010
V
DSNS2
to R
EXT
, V
DSNS1
to Diff-Amp +
1011
V
DSNS3
to R
EXT
, V
DSNS1
to Diff-Amp +
1100
V
DSNS4
to R
EXT
, V
DSNS1
to Diff-Amp +
1101
V
DSNS5
to R
EXT
, V
DSNS1
to Diff-Amp +
1110
V
DSNS6
to R
EXT
, V
DSNS1
to Diff-Amp +
1111
Normal Operation
相關PDF資料
PDF描述
MCZ33879AEK Configurable Octal Serial Switch with Open Load Detect Current Disable
MCZ33880EG Configurable Octal Serial Switch with Serial Peripheral Interface I/O
MCZ33883EG H-Bridge Gate Driver IC
MCZ33884EG Switch Monitor Interface
MCZ33887EK 5.0 A H-Bridge with Load Current Feedback
相關代理商/技術參數
參數描述
MCZ33800EKR2 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33800R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit
MCZ33810EK 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33810EK/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC
MCZ33810EKR2 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*