參數資料
型號： MCZ33977EG
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Single Gauge Driver
中文描述： 單表驅動
文件頁數： 30/37頁
文件大?。?/td> 402K
代理商： MCZ33977EG
Analog Integrated Circuit Device Data
Freescale Semiconductor
30
33977
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
bit will continue to indicate Logic [1] until the SPI message
following a detection of the zero position, or after the RTZ
feature is commanded OFF using the RTZ message.
0 = Return to Zero disabled
1 = Return to Zero enabled successfully
[Corrected original entry above to ACC2]
(ACC14:ACC0) Bits OD14:OD0
These 15 bits are from the RTZ accumulator. They
represent the integrated signal present on the non-driven coil
during an RTZ event. These bits are Logic [0] after power-on
reset, or after the
RST
pin transitions from Logic [0] to [1].
After an RTZ event, they will represent the last RTZ
accumulator result before the RTZ was stopped.
ACC14 is the MSB and is the sign bit used for zero
detection. Negative numbers have MSB Logic [1] and are
coded in twos complement.
Figure 13. RTZ Accumulator (Typical)
The analog-to-digital converter's linear input range covers
the expected magnitude of motor back e.m.f. signals, which
is usually less than 500mV. Input signals greater than this will
not cause any damage (the circuit is connected to the motor
H-Bridge drivers, and thus is exposed to the full magnitude of
the drive voltages), but may cause some small loss of
linearity. A typical plot of output vs. input is shown in
Figure 13
for 4ms step times.
GAUGE POINTER POSITION STATUS
INFORMATION
Most recent valid PECCR command resulting in the
Gauge Pointer Position status output:
The bits in
Table 18
are
read-only
bits.
(ENB) Bit OD15
This bit indicates whether the Gauge is enabled.
0 = Disabled
1 = Enabled
(DIR) Bit OD14
This bit indicates the direction the Gauge is moving.
0 = Toward position 0
1 = Away from position 0
(DIRC) Bit OD13
This bit is used to determine whether the direction of the
most recent pointer movement is toward the last commanded
position or away from it.
0 = Direction of the pointer movement is toward the
commanded position
1 = Direction of the pointer movement is away from the
commanded position
(CMD) Bit OD12
This bit indicates whether the gauge is at the most recently
commanded position.
0 = At commanded position
1 = Not at commanded position
D11
D10
D9
D8
1
1
0
0
omitted “don’t care--because N/A
Table 18. Gauge Pointer Position Status Output Register
Bits
OD15
OD14
OD13
OD12
OD11
OD10
OD9
OD8
OD7
OD6
OD5
OD4
OD3
OD2
OD1
OD0
Read
ENB
DIR
DIRC
CMD
POS11 POS10 POS9
POS8
POS7
POS5
POS5
POS4
POS3
POS2
POS1
POS0
Write
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
相關PDF資料
PDF描述
MCZ33989EG System Basis Chip with High-Speed CAN Transceiver
MCZ33990EF Enhanced Class B Serial Transceiver
MCZ33991EG Gauge Driver Integrated Circuit
MCZ33993EW Multiple Switch Detection Interface
MCZ33996EK 16-Output Switch with SPI Control
相關代理商/技術參數
參數描述
MCZ33977EG 制造商:Freescale Semiconductor 功能描述:IC STEPPER MOTOR GAUGE DRIVER SPI
MCZ33977EGR2 功能描述:馬達/運動/點火控制器和驅動器 SINGLE GAUGE DR. LG. PTR RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33989EG 功能描述:網絡控制器與處理器 IC SBC-HS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33989EG 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN TRANCEIVER
MCZ33989EGR2 功能描述:網絡控制器與處理器 IC SBC-HS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*