- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ34701EWR2 (飛思卡爾半導體(中國)有限公司) 1.5A Switch-Mode Power Supply with Linear Regulator PDF資料下載
參數資料
| 型號： | MCZ34701EWR2 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 1.5A Switch-Mode Power Supply with Linear Regulator |
| 中文描述： | 1.5A的開關模式電源，線性穩壓器 |
| 文件頁數： | 25/39頁 |
| 文件大小： | 528K |
| 代理商： | MCZ34701EWR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
34701
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Single 5.0V Supply, VIN1 = VIN2, or Dual Supply VIN1
≠
VIN2
The LDO supplies the microprocessor I/O voltage. The
switcher supplies the core (e.g., 1.5V nominal) (see
Figure 18
, page
23
).
Power-up
This condition depends upon the regulator current limit,
load current and capacitance, and the relative rise times of
the VIN1 and VIN2 supplies. There are two cases:
1.
LDO rises faster than VOUT
. The LDO uses control
methods (1) and (2) described in the section
Methods
of Control on page 23
.
2.
VOUT rises faster than LDO.
The switcher uses control
methods (5) and (6) described in the section
Methods
of Control on page 23
.
Power-down
This condition depends upon the regulator load current
and capacitance and the relative fall times of the VIN1 and
VIN2 supplies. There are two cases:
1.
VOUT falls faster than LDO.
The LDO uses control
methods (1) and (2) described in the section
Methods
of Control on page 23
.
In the case VIN1 = VIN2, the intrinsic operation turns
on both the buck high side MOSFET and the LDO
external Pass MOSFET, and discharges the LDO load
capacitor into the VIN supply.
2.
LDO falls faster than VOUT
The switcher uses control
methods (5) and (6) described in the section
Methods
of Control on page 23
.
Shorted Load
1.
VOUT shorted to ground.
The LDO uses method (1)
and (2) described in the section
Methods of Control on
page 23
.
2.
LDO shorted to ground.
The switcher uses control
methods (5) and (6) described in the section
Methods
of Control on page 23
.
3.
VIN1 shorted to ground.
Device is not working.
4.
VIN2 shorted to ground with VIN1 and VIN2 different.
This is equivalent to the switcher output shorted to
ground.
5.
VOUT shorted to supply.
No load protection. 34701 is
protected by current limit and thermal shutdown.
6.
LDO shorted to supply.
No load protection. 34701 is
protected by current limit and thermal shutdown.
INVERTED OPERATING MODE
Single 3.3V Supply, VIN = VIN1 = VIN2 = 3.3V
The 3.3V supplies the microprocessor I/O voltage, the
LDO supplies core voltage (e.g., 1.5V nominal), and the
switcher VOUT operates independently. Power sequencing
depends only on the normal LDO intrinsic operation to control
the Pass MOSFET.
Power-up
When VIN is rising, initially LDO is below the regulation
point and the Pass MOSFET is on. In order not to exceed the
2.1V differential requirement between the I/O (VIN) and the
core (LDO), the LDO must start up at 2.1V or less and be able
to maintain the 2.1V or less differential. The maximum slew
rate for V
IN
is 1.0V/ms.
Power-down
When VIN is falling, LDO falls below the regulation point;
therefore, the Pass MOSFET is on. In the case where LDO is
falling faster than VIN, the pass MOSFET attempts to
maintain LDO. In the case where VIN is falling faster than
LDO, the pass MOSFET is also on, and the LDO load
capacitor is discharged through the pass MOSFET to VIN.
Thus, provided VIN does not fall too fast, the core voltage
(LDO) does not exceed the I/O voltage (VIN) by more than
maximum of 0.4V.
Shorted Load
1.
LDO shorted to ground.
This will cause the I/O voltage
to exceed the core voltage by more than 2.1V. No load
protection.
2.
VIN shorted to ground.
Until the LDO load capacitance
is discharged, the core voltage exceeds the I/O voltage
by more than 0.4V. By the intrinsic operation of the
LDO, the load capacitor is discharged rapidly through
the Pass MOSFET to VIN.
3.
LDO shorted to supply.
No load protection.
Single 5.0V Supply, VIN1 = VIN2, or Dual Supply VIN1
≠
VIN2
The switcher VOUT supplies the microprocessor I/O
voltage. The LDO supplies the core (e.g., 1.5V nominal) (see
Figure 19
, page
23
).
Power-up
This condition depends upon the regulator current limit,
load current and capacitance, and the relative rise times of
the VIN1 and VIN2 supplies. There are two cases:
1.
VOUT rises faster than LDO.
The switcher VOUT uses
control methods (1) and (2) described in the section
Methods of Control on page 23
.
2.
LDO rises faster than VOUT
The LDO uses control
methods (5) and (6) described in the section
Methods
of Control on page 23
.
Power-down
This condition depends upon the regulator load current
and capacitance and the relative fall times of the VIN1 and
VIN2 supplies. There are two cases:
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ79076EG | Electronic Ignition Control Circuit |
| MD-S5007 | Analog IC |
| MD-S5008 | Analog IC |
| MD-S5010 | Analog IC |
| MD100 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ34702EW | 功能描述:低壓差穩壓器 - LDO QUICCSUPPLY 2 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCZ34702EWR2 | 功能描述:低壓差穩壓器 - LDO QUICCSUPPLY 2 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCZ36304201 | 制造商:LG Corporation 功能描述:Duct |
| MCZ36305001 | 制造商:LG Corporation 功能描述:Duct |
| MCZ36444401 | 制造商:LG Corporation 功能描述:Duct |
發布緊急采購，3分鐘左右您將得到回復。