- 您現在的位置：買賣IC網 > PDF目錄45386 > MD83C154XXX-16P883D (TEMIC SEMICONDUCTORS) 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 PDF資料下載
參數資料
| 型號： | MD83C154XXX-16P883D |
| 廠商： | TEMIC SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 |
| 文件頁數： | 33/232頁 |
| 文件大小： | 61013K |
| 代理商： | MD83C154XXX-16P883D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁
128
ATtiny25/45/85 [DATASHEET]
2586Q–AVR–08/2013
17.6
Changing Channel or Reference Selection
The MUX[3:0] and REFS[2:0] bits in the ADMUX Register are single buffered through a temporary register to which
the CPU has random access. This ensures that the channels and voltage reference selection only takes place at a
safe point during the conversion. The channel and voltage reference selection is continuously updated until a con-
version is started. Once the conversion starts, the channel and voltage reference selection is locked to ensure a
sufficient sampling time for the ADC. Continuous updating resumes in the last ADC clock cycle before the conver-
sion completes (ADIF in ADCSRA is set). Note that the conversion starts on the following rising ADC clock edge
after ADSC is written. The user is thus advised not to write new channel or voltage reference selection values to
ADMUX until one ADC clock cycle after ADSC is written.
If Auto Triggering is used, the exact time of the triggering event can be indeterministic. Special care must be taken
when updating the ADMUX Register, in order to control which conversion will be affected by the new settings.
If both ADATE and ADEN is written to one, an interrupt event can occur at any time. If the ADMUX Register is
changed in this period, the user cannot tell if the next conversion is based on the old or the new settings. ADMUX
can be safely updated in the following ways:
a.
When ADATE or ADEN is cleared.
b.
During conversion, minimum one ADC clock cycle after the trigger event.
c.
After a conversion, before the Interrupt Flag used as trigger source is cleared.
When updating ADMUX in one of these conditions, the new settings will affect the next ADC conversion.
17.6.1
ADC Input Channels
When changing channel selections, the user should observe the following guidelines to ensure that the correct
channel is selected:
In Single Conversion mode, always select the channel before starting the conversion. The channel selection may
be changed one ADC clock cycle after writing one to ADSC. However, the simplest method is to wait for the con-
version to complete before changing the channel selection.
In Free Running mode, always select the channel before starting the first conversion. The channel selection may
be changed one ADC clock cycle after writing one to ADSC. However, the simplest method is to wait for the first
conversion to complete, and then change the channel selection. Since the next conversion has already started
automatically, the next result will reflect the previous channel selection. Subsequent conversions will reflect the
new channel selection.
17.6.2
ADC Voltage Reference
The voltage reference for the ADC (V
REF) indicates the conversion range for the ADC. Single ended channels that
exceed V
REF will result in codes close to 0x3FF. VREF can be selected as either VCC, or internal 1.1V / 2.56V volt-
age reference, or external AREF pin. The first ADC conversion result after switching voltage reference source may
be inaccurate, and the user is advised to discard this result.
17.7
ADC Noise Canceler
The ADC features a noise canceler that enables conversion during sleep mode to reduce noise induced from the
CPU core and other I/O peripherals. The noise canceler can be used with ADC Noise Reduction and Idle mode. To
make use of this feature, the following procedure should be used:
Make sure that the ADC is enabled and is not busy converting. Single Conversion mode must be selected and
the ADC conversion complete interrupt must be enabled.
Enter ADC Noise Reduction mode (or Idle mode). The ADC will start a conversion once the CPU has been
halted.
If no other interrupts occur before the ADC conversion completes, the ADC interrupt will wake up the CPU and
execute the ADC Conversion Complete interrupt routine. If another interrupt wakes up the CPU before the ADC
相關PDF資料 |
PDF描述 |
|---|---|
| MR80C154-L16/883 | 8-BIT, 16 MHz, MICROCONTROLLER, CQCC44 |
| MR83C154TXXX-16/883 | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQCC44 |
| MR83C154TXXX-20/883 | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQCC44 |
| MR80C154-25P883 | 8-BIT, 25 MHz, MICROCONTROLLER, CQCC44 |
| MR83C154DXXX-12P883D | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MD8412B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LINK(IEEE 1394) |
| MD8451H-8/B | 制造商:undefined 功能描述: |
| MD845A-R2 | 制造商:Black Box Corporation 功能描述:MODEM 202 |
| MD845A-R2-W1 | 制造商:Black Box Corporation 功能描述:1 YEAR WARRANTY FOR MD845A-R2 |
| MD845A-R2-W3 | 制造商:Black Box Corporation 功能描述:3 YEAR WARRANTY FOR MD845A-R2 |
發布緊急采購，3分鐘左右您將得到回復。