參數資料
型號: MGA-81563-TR1
英文描述: 0.1- 6 GHz 3 V, 14 dBm Amplifier
中文描述: 0.1 - 6 GHz的3伏,14 dBm的放大器
文件頁數: 9/12頁
文件大?。?/td> 135K
代理商: MGA-81563-TR1
6-204
N
1
SUPPLY VOLTAGE (V)
0
2
4
8
6
18
10
12
14
16
NF
Gain
Power
0
3
4
5
1
2
Figure 20. Gain, Noise Figure, and
Output Power vs. Supply Voltage.
Some thermal precautions must
be observed for operation at
higher bias voltages. For reliable
operation, the channel tempera-
ture should be kept within the
165
°
C indicated in the “Absolute
Maximum Ratings” table. As a
guideline, operating life tests have
established a MTTF in excess of
10
6
hours for channel tempera-
tures up to 150
°
C.
There are several means of biasing
the MGA-81563 at 3 volts in
systems that use higher power
supply voltages. The simplest
method, shown in Figure 21a, is to
use a series resistor to drop the
device voltage to 3 volts. For
example, a 47
resistor will drop
a 5-volt supply to 3 volts at the
nominal current of 42 mA. Some
variation in performance could be
expected for this method due to
variations in current within the
specified 31 to 51 mA min/max
range.
47
(a)
+5 V
Silicon
Diodes
(b)
+5 V
Zener
Diode
(c)
+5 V
Figure 21. Biasing From Higher
Supply Voltages.
A second method illustrated in
Figure 21b, is to use forward-
biased diodes in series with the
power supply. For example, three
silicon diodes connected in series
will drop a 5-volt supply to
approximately 3 volts.
The use of the series diode
approach has the advantage of
less dependency on current
variation in the amplifiers since
the forward voltage drop of a
diode is somewhat current
independent.
Reverse breakdown diodes (e.g.,
Zener diodes) could also be used
as in Figure 21c. However, care
should be taken to ensure that the
noise generated by diodes in
either Zener or reverse break-
down is adequately filtered (e.g.,
bypassed to ground) such that the
diode’s noise is not added to the
amplifier’s signal.
SOT-363 PCB Footprint
A recommended PCB pad layout
for the miniature SOT-363 (SC-70)
package used by the MGA-81563 is
shown in Figure 22 (dimensions
are in inches). This layout pro-
vides ample allowance for pack-
age placement by automated
assembly equipment without
adding parasitics that could
impair the high frequency RF
performance of the MGA-81563.
The layout is shown with a
nominal SOT-363 package foot-
print superimposed on the PCB
pads.
0.026
0.035
0.075
0.016
Figure 22. PCB Pad Layout
(dimensions n nches).
SMT Assembly
Reliable assembly of surface
mount components is a complex
process that involves many
material, process, and equipment
factors, including: method of
heating (e.g., IR or vapor phase
reflow, wave soldering, etc.)
circuit board material, conductor
thickness and pattern, type of
solder alloy, and the thermal
conductivity and thermal mass of
components. Components with a
low mass, such as the SOT-363
package, will reach solder reflow
temperatures faster than those
with a greater mass.
相關PDF資料
PDF描述
MGA-82563-TR1 0.1-6 GHz 3V, 17 dBm Amplifier
MGB2310TK-X 128 x 64 pixel format, LED or EL Backlight available
MGB27TA-X ULTRA HIGH BRIGHTNESS GREEN LED LAMP
MGB31TA-X ULTRA HIGH BRIGHTNESS GREEN LED LAMP
MGB31TAH ULTRA HIGH BRIGHTNESS GREEN LED LAMP
相關代理商/技術參數
參數描述
MGA-81563-TR1G 功能描述:射頻放大器 3 SV 12.4 dB RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
MGA-81563-TR2G 功能描述:射頻放大器 3 SV 12.4 dB RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
MGA82563 制造商:AGILENT 制造商全稱:AGILENT 功能描述:0.1-6 GHz 3V, 17 dBm Amplifier
MGA-82563 制造商:AGILENT 制造商全稱:AGILENT 功能描述:0.1-6 GHz 3V, 17 dBm Amplifier
MGA-82563-1HAG 制造商:Avago Technologies 功能描述:3V MINIATURE 17 DBM POWER AMP WITH HAA TAPE LEAD FREE - Bulk