- 您現在的位置：買賣IC網 > PDF目錄359164 > MGCM02BP1Q (Zarlink Semiconductor Inc.) TDMA/AMPS IF and Baseband Interface PDF資料下載
參數資料
| 型號： | MGCM02BP1Q |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | TDMA/AMPS IF and Baseband Interface |
| 中文描述： | 時分多址/ AMPS二元IF和基帶接口 |
| 文件頁數： | 12/21頁 |
| 文件大?。?/td> | 529K |
| 代理商： | MGCM02BP1Q |
MGCM02
Data Sheet
12
Input Signal (dBm)
RSSI
Output
(V)
V
DD
/2
Figure 6 - RSSI Characteristic
Transmit
TDMA IS136 Mode I/Q Modulation
The inputs to MGCM02 are derived from baseband
digital to analog converters. These signals are
passed through variable gain buffers. The gain of
these buffers can be programmed from 0 to 12 dB in
3 dB increments allowing compatibility with a number
of baseband and transmit modulator devices.
The buffers are followed by reconstruction
fi
lters to
remove spurious responses from preceding digital to
analog converters. These
fi
lters are third order
Butterworth with 25kHz cut off. The
fi
lters contain
automatic calibration to set the cut off frequency.
This can be controlled via the serial programming
bus.
All inputs and outputs are differential
AMPS FM mode
There
accommodate the modulation technique used and
different baseband interfaces.
is
a
choice
of
modes
available
to
If I,Q modulation is used for FM modulation then the
same mode is used as for TDMA ie differential input
and differential output on the I and Q channels.
If direct modulation of the transmit IF VCO is used
then the TX FM (E5) single-ended output is used.
The I+,Q+ outputs are switched high and the I-,Q-
outputs are switched low to set the IQ modulator in a
transmit device such as the Zarlink MGCT04 into FM
mode. When using the MGCT04 the transmit IF VCO
will be operating at twice the IF frequency. The
frequency deviation therefore required on the VCO
will be twice that required at the transmit output of
that device.
The input to the MGCM02 can be programmed to be
either differential or single ended using the I channel
inputs and the Q channel inputs are powered down.
The differential input mode is the same as for TDMA.
In the single ended mode only the TXI+ input is
active and the FM signal must be capacitively
coupled into this pin. This mode would only be used
where the FM signal is from a different source to the
I channel. When using this mode the differential I
outputs from a baseband device must be in high
impedance state.
The transmit
fi
ltering used for FM mode is the same
as for TDMA mode.
Synthesisers and VCO
Two VHF PLL synthsisers are included for the
generation of receive and transmit IF LO signals. The
two synthesisers are identical.
The input to the receive PLL is from the on chip VCO.
This operates at twice the LO frequency. An external
tank circuit is required - typically a parallel capacitor
and inductor with a varactor for tuning.
相關PDF資料 |
PDF描述 |
|---|---|
| MGCM02KG | TDMA/AMPS IF and Baseband Interface |
| MGCT04LH1S | Transmit Circuit for TDMA/AMPS and CDMA/AMPS |
| MGCT04LH1T | Transmit Circuit for TDMA/AMPS and CDMA/AMPS |
| MGCT04 | Transmit Circuit for TDMA/AMPS and CDMA/AMPS |
| MGCT04KG | Transmit Circuit for TDMA/AMPS and CDMA/AMPS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MGCM02KG | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:TDMA/AMPS IF and Baseband Interface |
| MGCOV | 功能描述:繼電器插座與硬件 RELAY COVER RoHS:否 制造商:TE Connectivity / Schrack 附件類型:Socket 相關繼電器系列:RP, RT, RY 端接類型:PCB 極數:1 |
| MGCR01 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Dual Mode IF Receiver for TDMA/AMPS and CDMA/AMPS |
| MGCR01KG | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Dual Mode IF Receiver for TDMA/AMPS and CDMA/AMPS |
| MGCR01QP1S | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Dual Mode IF Receiver for TDMA/AMPS and CDMA/AMPS |
發布緊急采購，3分鐘左右您將得到回復。