- 您現在的位置：買賣IC網 > PDF目錄383611 > MIC4721YMM (MICREL INC) Dual UART with 64-byte FIFO, SOT313-2 (LQFP48), Reel Pack, SMD, 13", Turned PDF資料下載
參數資料
| 型號： | MIC4721YMM |
| 廠商： | MICREL INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Dual UART with 64-byte FIFO, SOT313-2 (LQFP48), Reel Pack, SMD, 13", Turned |
| 中文描述： | 11 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | LEAD FREE, MSOP-10 |
| 文件頁數： | 11/19頁 |
| 文件大?。?/td> | 827K |
| 代理商： | MIC4721YMM |
Micrel, Inc.
MIC4721
Efficiency Considerations
Calculating the efficiency is as simple as measuring
power out and dividing it by the power in.
P
Efficiency
May 2007
11
M9999-052907-A
100
×
=
IN
OUT
P
Where input power (P
IN
) is:
P
IN
= V
IN
× I
IN
and output power (P
OUT
) is calculated as:
P
OUT
= V
OUT
× I
OUT
The Efficiency of the MIC2207 is determined by several
factors.
R
DSON
(Internal P-channel Resistance)
Diode conduction losses
Inductor Conduction losses
Switching losses
R
DSON
losses
are caused by the current flowing through
the high side P-channel MOSFET. The amount of power
loss can be approximated by:
P
SW
= R
DSON
× I
OUT
2
× D
Where D is the duty cycle.
Since the MIC4721 uses an internal P-channel
MOSFET, R
DSON
losses are inversely proportional to
supply voltage. Higher supply voltage yields a higher
gate to source voltage, reducing the R
DSON
, thus
reducing the MOSFET conduction losses. A graph
showing typical R
DSON
vs. input supply voltage can be
found in the typical characteristics section of this
datasheet.
Diode conduction losses
occur due to the forward
voltage drop (VF) and the output current. Diode power
losses can be approximated as follows:
P
D
= V
F
× I
OUT
× (1 – D)
For this reason, the low forward voltage drop Schottky
diode is the rectifier of choice. The low forward voltage
drop will help reduce diode conduction losses, and
improve efficiency. Duty cycle, or the ratio of output
voltage to input voltage, determines whether the
dominant factor in conduction losses will be the internal
MOSFET or the Schottky diode. Higher duty cycles
place the power losses on the high side switch, and
lower duty cycles place the majority of power loss on the
Schottky diode.
Inductor conduction losses
(PL) can be calculated by
multiplying the DC resistance (DCR) times the square of
the output current:
P
L
= DCR × I
OUT
2
Also, be aware that there are additional core losses
associated with switching current in an inductor. Since
most inductor manufacturers do not give data on the
type of material used, approximating core losses
becomes very difficult, so verify inductor temperature
rise.
Switching losses
occur twice each cycle, when the
switch turns on and when the switch turns off. This is
caused by a non-ideal world where switching transitions
are not instantaneous, and neither are current
transitions. Figure 6 demonstrates (or exaggerates…)
how switching losses due to the transitions dissipate
power in the switch.
Figure 6. Switching Transition Losses
Normally, when the switch is on, the voltage across the
switch is low (virtually zero) and the current through the
switch is high. This equates to low power dissipation.
When the switch is off, voltage across the switch is high
and the current is zero, again with power dissipation
being low. During the transitions, the voltage across the
switch (VS-D) and the current through the switch (IS-D)
are at midpoint of their excursions and cause the
transition to be the highest instantaneous power point.
During continuous mode, these losses are the highest.
Also, with higher load currents, these losses are higher.
For discontinuous operation, the transition losses only
occur during the “off” transition since the “on” transitions
there is no current flow through the inductor.
Component Selection
Input Capacitor
A 10μF ceramic is recommended on each VIN pin for
bypassing. X5R or X7R dielectrics are recommended for
the input capacitor. Y5V dielectrics lose most of their
capacitance over temperature and voltage and are
therefore not recommended. Also, tantalum and
electrolytic capacitors alone are not recommended
because of their reduced RMS current handling,
reliability, and higher ESR. Smaller case size capacitors
are recommended due to their lower ESL (equivalent
series
inductance).
Please
recommendations for proper layout of the input
capacitors.
refer
to
layout
相關PDF資料 |
PDF描述 |
|---|---|
| MIC4722 | 3mm x 3mm 2.7MHz 3A PWM Buck Regulator |
| MIC4722YML | 3mm x 3mm 2.7MHz 3A PWM Buck Regulator |
| MIC4807 | 80V 8-Channel Addressable Low-Side Driver |
| MIC4807BN | 80V 8-Channel Addressable Low-Side Driver |
| MIC4826 | Low Input Voltage, 160VPP Output Voltage, EL Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC4721YMM TR | 功能描述:直流/直流開關調節器 1.5A 2MHz Buck Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MIC4721YMMTR | 功能描述:IC REG BUCK ADJ 1.5A 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| MIC4722 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3mm x 3mm 2.7MHz 3A PWM Buck Regulator |
| MIC4722_10 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3mm x 3mm 2.7MHz 3A PWM Buck Regulator |
| MIC4722YML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。