- 您現在的位置：買賣IC網 > PDF目錄377970 > ML4804IP (FAIRCHILD SEMICONDUCTOR CORP) Power Factor Correction and PWM Controller Combo PDF資料下載
參數資料
| 型號： | ML4804IP |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Power Factor Correction and PWM Controller Combo |
| 中文描述： | 1 A POWER FACTOR CONTROLLER WITH POST REGULATOR, 250 kHz SWITCHING FREQ-MAX, PDIP16 |
| 封裝： | PLASTIC, DIP-16 |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 145K |
| 代理商： | ML4804IP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁
ML4804
12
REV. 1.0.2 3/9/2001
Generating V
CC
The ML4804 is a voltage-fed part. It requires an external
15V,
±
10% (or better) shunt voltage regulator, or some
other V
CC
regulator, to regulate the voltage supplied to
the part at 15V nominal. This allows low power dissipation
while at the same time delivering 13V nominal gate drive
at the PWM OUT and PFC OUT outputs. If using a Zener
diode for this function, it is important to limit the current
through the Zener to avoid overheating or destroying it.
This can be easily done with a single resistor in series
with the Vcc pin, returned to a bias supply of typically
18V to 20V. The resistor
’
s value must be chosen to meet
the operating current requirement of the ML4804 itself
(8.5mA, max.) plus the current required by the two gate
driver outputs.
EXAMPLE:
With a V
BIAS
of 20V, a V
CC
of 15V and the ML4804
driving a total gate charge of 90nC at 100kHz (e.g., 1
IRF840 MOSFET and 2 IRF820 MOSFETs), the gate driver
current required is:
=
×
(
(
(7)
(8)
Choose R
BIAS
< 240
The ML4804 should be locally bypassed with a 1.0
μ
F
ceramic capacitor. In most applications, an electrolytic
capacitor of between 47
μ
F and 220
μ
F is also required
across the part, both for filtering and as part of the start-up
bootstrap circuitry.
LEADING/TRAILING MODULATION
Conventional Pulse Width Modulation (PWM) techniques
employ trailing edge modulation in which the switch will
turn on right after the trailing edge of the system clock.
The error amplifier output voltage is then compared with
the modulating ramp. When the modulating ramp reaches
the level of the error amplifier output voltage, the switch
will be turned OFF. When the switch is ON, the inductor
current will ramp up. The effective duty cycle of the
trailing edge modulation is determined during the ON
time of the switch. Figure 4 shows a typical trailing edge
control scheme.
In the case of leading edge modulation, the switch is
turned OFF right at the leading edge of the system clock.
When the modulating ramp reaches the level of the error
amplifier output voltage, the switch will be turned ON.
The effective duty-cycle of the leading edge modulation
is determined during the OFF time of the switch. Figure 5
shows a leading edge control scheme.
One of the advantages of this control technique is that it
requires only one system clock. Switch 1 (SW1) turns off
and switch 2 (SW2) turns on at the same instant to
minimize the momentary
“
no-load
”
period, thus lowering
ripple voltage generated by the switching action. With
such synchronized switching, the ripple voltage of the
first stage is reduced. Calculation and evaluation have
shown that the 120Hz component of the PFC
’
s output
ripple voltage can be reduced by as much as 30% using
this method.
TYPICAL APPLICATIONS
Figure 6 is the application circuit for a complete 100W
power factor corrected power supply, designed using the
methods and general topology detailed in Application
Note 33.
Figure 5. Typical Leading Edge Control Scheme
FUNCTIONAL DESCRIPTION
(Continued)
"#$
=
$
)
)
=
+
+
!
!
!$
)
=
+
=
(
REF
EA
–
+
–
+
OSC
DFF
R
D
Q
Q
CLK
U1
RAMP
CLK
U4
U3
C1
RL
I4
SW2
SW1
+
DC
I1
I2
I3
VIN
L1
VEAO
CMP
U2
RAMP
VEAO
TIME
VSW1
TIME
相關PDF資料 |
PDF描述 |
|---|---|
| ML4804IS | Power Factor Correction and PWM Controller Combo |
| ML4804 | Power Factor Correction and PWM Controller Combo(功率因數校正器和PWM控制器組合芯片) |
| ML4805 | Variable Feedforward PFC/PWM Controller Combo |
| ML4805CP | Variable Feedforward PFC/PWM Controller Combo |
| ML4805CS | Variable Feedforward PFC/PWM Controller Combo |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML4804IS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Power Factor Correction and PWM Controller Combo |
| ML4805 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Variable Feedforward PFC/PWM Controller Combo |
| ML4805CP | 功能描述:功率因數校正 IC DIP-18 RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| ML4805CS | 功能描述:功率因數校正 IC SOIC-WIDE-18 RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| ML4805CSX | 功能描述:功率因數校正 IC SOIC-WIDE-18 RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。