- 您現在的位置：買賣IC網 > PDF目錄377970 > ML4805CS (FAIRCHILD SEMICONDUCTOR CORP) Variable Feedforward PFC/PWM Controller Combo PDF資料下載
參數資料
| 型號： | ML4805CS |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Variable Feedforward PFC/PWM Controller Combo |
| 中文描述： | 0.5 A POWER FACTOR CONTROLLER WITH POST REGULATOR, 212 kHz SWITCHING FREQ-MAX, PDSO18 |
| 封裝： | PLASTIC, SOIC-18 |
| 文件頁數： | 9/13頁 |
| 文件大小： | 125K |
| 代理商： | ML4805CS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁
ML4805
REV. 1.1 3/9/2001
9
operating frequency can typically be approximated by:
(5)
EXAMPLE:
For the application circuit shown in the data sheet, with
the oscillator running at:
Solving for R
T
x C
T
yields 2 x 10
-4
. Selecting standard
components values, C
T
= 270pF, and R
T
= 36.5k
.
T
T
.
PWM SECTION
Pulse Width Modulator
The PWM section of the ML4805 is straightforward, but
there are several points which should be noted. Foremost
among these is its inherent synchronization to the PFC
section of the device. The PWM is capable of current-
mode or voltage mode operation. In current-mode
applications, the PWM ramp (RAMP 2) is usually derived
directly from a current sensing resistor or current
transformer in the primary of the output stage, and is
thereby representative of the current flowing in the
converter
’
LIMIT
, which provides
cycle-by-cycle current limiting, is typically connected to
RAMP 2 in such applications. For voltage-mode operation
or certain specialized applications, RAMP 2 can be
connected to a separate RC timing network to generate a
voltage ramp against which V
these conditions, the use of voltage feedforward from the
PFC buss can assist in line regulation accuracy and
response. As in current mode operation, the DC I
LIMIT
input is used for output stage overcurrent protection.
No voltage error amplifier is included in the PWM stage
of the ML4805, as this function is generally performed on
the output side of the PWM
’
s isolation boundary. To
facilitate the design of optocoupler feedback circuitry, an
offset has been built into the PWM
’
s RAMP 2 input which
allows V
input voltages below 1.25V.
PWM Current Limit
The DC I
pin is a direct input to the cycle-by-cycle
current limiter for the PWM section. Should the input
voltage at this pin ever exceed 1.5V, the output of the
PWM will be disabled until the output flip-flop is reset by
the clock pulse at the start of the next PWM power cycle.
V
IN
OK Comparator
V
The V
PFC and inhibits the PWM if this voltage on V
FB
is less
than its nominal 2.5V. Once this voltage reaches 2.5V,
which corresponds to the PFC output capacitor being
charged to its rated boost voltage, the soft-start
commences.
PWM Control (RAMP 2)
When the PWM section is used in current mode, RAMP 2
is generally used as the sampling point for a voltage
representing the current in the primary of the PWM
’
s
output transformer, derived either by a current sensing
resistor or a current transformer. In voltage mode, it is the
input for a ramp voltage generated by a second set of
timing components (R
RAMP2
, C
RAMP2
), which will have a
minimum value of zero volts and should have a peak
value of approximately 5V. In voltage mode operation,
feedforward from the PFC output buss is an excellent way
to derive the timing ramp for the PWM stage.
Soft Start
Start-up of the PWM is controlled by the selection of the
external capacitor at SS. A current source of 25
μ
A
supplies the charging current for the capacitor, and start-
up of the PWM begins at 1.25V. Start-up delay can be
programmed by the following equation:
μ
(6)
where C
SS
is the required soft start capacitance, and
t
DELAY
is the desired start-up delay.
t
It is important that the time constant of the PWM soft-start
allow the PFC time to generate sufficient output power for
the PWM section. The PWM start-up delay should be at
least 5ms.
Solving for the minimum value of C
SS
:
:
In the ML4805, the operating frequency of the PFC
section is fixed at 1/2 of the PWM's operating frequency.
This is done through the use of a 2:1 digital frequency
divider ("T" flip-flop) linking the two functional sections of
the IC.
FUNCTIONAL DESCRIPTION
(Continued)
!"#
T
T
-4
’
s output stage. DC I
DC
will be compared. Under
’
’
DC
to command a zero percent duty cycle for
LIMIT
IN
OK comparator monitors the DC output of the
’
s
$%
=
×
&
=
×
=
μ
相關PDF資料 |
PDF描述 |
|---|---|
| ML4805IP | Variable Feedforward PFC/PWM Controller Combo |
| ML4805IS | Variable Feedforward PFC/PWM Controller Combo |
| ML4810 | High Frequency PWM Controller(高頻PWM控制器) |
| ML4811 | High Frequency PWM Controller(高頻PWM控制器) |
| ML4812IQ | Power Factor Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML4805CSX | 功能描述:功率因數校正 IC SOIC-WIDE-18 RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| ML4805IP | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Variable Feedforward PFC/PWM Controller Combo |
| ML4805IS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Variable Feedforward PFC/PWM Controller Combo |
| ML4810 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:High Frequency Power Supply Controller |
| ML4810CP | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:High Frequency Power Supply Controller |
發布緊急采購，3分鐘左右您將得到回復。