- 您現在的位置：買賣IC網 > PDF目錄45360 > MPC8343EVRADDX (FREESCALE SEMICONDUCTOR INC) 32-BIT, 266 MHz, MICROPROCESSOR, PBGA620 PDF資料下載
參數資料
| 型號： | MPC8343EVRADDX |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, 266 MHz, MICROPROCESSOR, PBGA620 |
| 封裝： | 29 X 29 MM, 2.46 MM HEIGHT, 1 MM PITCH, LEAD FREE, PLASTIC, BGA-620 |
| 文件頁數： | 84/92頁 |
| 文件大小： | 987K |
| 代理商： | MPC8343EVRADDX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁當前第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
MPC8343E PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 6
Freescale Semiconductor
85
System Design Information
pull-up/pull-down resistors coupled with the large value of the pull-up/pull-down resistor should minimize
the disruption of signal quality or speed for output pins thus configured.
20.7
Pull-Up Resistor Requirements
The MPC8343E requires high resistance pull-up resistors (10 k
is recommended) on open drain type pins
including I2C pins, Ethernet Management MDIO pin and EPIC interrupt pins.
Correct operation of the JTAG interface requires configuration of a group of system control pins as
demonstrated in Figure 36. Care must be taken to ensure that these pins are maintained at a valid deasserted
state under normal operating conditions as most have asynchronous behavior and spurious assertion will
give unpredictable results.
Refer to the PCI 2.2 specification for all pull-ups required for PCI.
20.8
JTAG Configuration Signals
Boundary scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the
IEEE 1149.1 specification, but is provided on all processors that implement the PowerPC architecture. The
MPC8343E requires TRST to be asserted during reset conditions to ensure the JTAG boundary logic does
not interfere with normal chip operation. While it is possible to force the TAP controller to the reset state
using only the TCK and TMS signals, generally systems will assert TRST during power-on reset. Because
the JTAG interface is also used for accessing the common on-chip processor (COP) function, simply tying
TRST to PORESET is not practical.
The COP function of these processors allows a remote computer system (typically, a PC with dedicated
hardware and debugging software) to access and control the internal operations of the processor. The COP
interface connects primarily through the JTAG port of the processor, with some additional status
monitoring signals. The COP port requires the ability to independently assert TRST without causing
PORESET. If the target system has independent reset sources, such as voltage monitors, watchdog timers,
power supply failures, or push-button switches, then the COP reset signals must be merged into these
signals with logic.
The arrangement shown in Figure 36 allows the COP to independently assert HRESET or TRST, while
ensuring that the target can drive HRESET as well. If the JTAG interface and COP header will not be used,
TRST should be tied to PORESET so that it is asserted when the system reset signal (PORESET) is
asserted.
The COP header shown Figure 36 in adds many benefits—breakpoints, watchpoints, register and memory
examination/modification, and other standard debugger features are possible through this interface—and
can be as inexpensive as an unpopulated footprint for a header to be added when needed.
The COP interface has a standard header for connection to the target system, based on the 0.025"
square-post, 0.100" centered header assembly (often called a Berg header).
There is no standardized way to number the COP header shown in Figure 36; consequently, many different
pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then
left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter
相關PDF資料 |
PDF描述 |
|---|---|
| MPC8343EZQADDX | 32-BIT, 266 MHz, MICROPROCESSOR, PBGA620 |
| MPC8343CZQADDX | 32-BIT, 266 MHz, MICROPROCESSOR, PBGA620 |
| MPC8343CVRADDX | 32-BIT, 266 MHz, MICROPROCESSOR, PBGA620 |
| MPC8343ZQAGDX | 32-BIT, 400 MHz, MICROPROCESSOR, PBGA620 |
| MPC8343EZQAGDX | 32-BIT, 400 MHz, MICROPROCESSOR, PBGA620 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC8343EVRAGD | 功能描述:IC MPU PWRQUICC II PRO 620-PBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:MPC83xx 標準包裝:1 系列:MPC85xx 處理器類型:32-位 MPC85xx PowerQUICC III 特點:- 速度:1.2GHz 電壓:1.1V 安裝類型:表面貼裝 封裝/外殼:783-BBGA，F(xiàn)CBGA 供應商設備封裝:783-FCPBGA（29x29） 包裝:托盤 |
| MPC8343EVRAGDB | 功能描述:微處理器 - MPU 8347 PBGA NOPB W/ENC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC8343EVRAGDB | 制造商:Freescale Semiconductor 功能描述:Embedded Networking Processor |
| MPC8343EZQADD | 功能描述:IC MPU PWRQUICC II PRO 620-PBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:MPC83xx 標準包裝:1 系列:MPC85xx 處理器類型:32-位 MPC85xx PowerQUICC III 特點:- 速度:1.2GHz 電壓:1.1V 安裝類型:表面貼裝 封裝/外殼:783-BBGA，F(xiàn)CBGA 供應商設備封裝:783-FCPBGA（29x29） 包裝:托盤 |
| MPC8343EZQADDB | 功能描述:微處理器 - MPU 8347 PBGA PB W/ ENC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
發布緊急采購，3分鐘左右您將得到回復。