參數資料
型號： MPC8377EVRAGD
廠商： Freescale Semiconductor
文件頁數： 109/127頁
文件大?。?/td> 0K
描述： MPU PWRQUICC II 400MHZ 689TEPBGA
產品培訓模塊： MPC837x PowerQUICC II Pro Processors
視頻文件： Introduction to the MPC837x Family
標準包裝： 27
系列： MPC83xx
處理器類型： 32-位 MPC83xx PowerQUICC II Pro
速度： 400MHz
電壓： 1V
安裝類型： 表面貼裝
封裝/外殼： 689-BBGA 裸露焊盤
供應商設備封裝： 689-TEPBGA II（31x31）
包裝： 托盤
配用： MPC8377E-RDBA-ND - BOARD REF DES MPC8377 REV 2.1
MPC8377E-MDS-PB-ND - BOARD MODULAR DEV SYSTEM
MPC8377E PowerQUICC II Pro Processor Hardware Specifications, Rev. 8
82
Freescale Semiconductor
greater than 200 mV. This requirement is the same for both external DC-coupled or
AC-coupled connection.
— For external DC-coupled connection, as described in Section 21.2.1, “SerDes Reference
Clock Receiver Characteristics,” the maximum average current requirements sets the
requirement for average voltage (common mode voltage) to be between 100 mV and 400 mV.
Figure 53 shows the SerDes reference clock input requirement for DC-coupled connection
scheme.
— For external AC-coupled connection, there is no common mode voltage requirement for the
clock driver. Since the external AC-coupling capacitor blocks the DC level, the clock driver
and the SerDes reference clock receiver operate in different command mode voltages. The
SerDes reference clock receiver in this connection scheme has its common mode voltage set to
SGND_SRDSn. Each signal wire of the differential inputs is allowed to swing below and above
the command mode voltage (SGND_SRDSn). Figure 54 shows the SerDes reference clock
input requirement for AC-coupled connection scheme.
Single-ended Mode
— The reference clock can also be single-ended. The SD _REF_CLK input amplitude
(single-ended swing) must be between 400 mV and 800 mVp-p (from Vmin to Vmax) with
SDn_REF_CLK either left unconnected or tied to ground.
—The SDn_REF_CLK input average voltage must be between 200 mV and 400 mV. Figure 55
shows the SerDes reference clock input requirement for single-ended signaling mode.
— To meet the input amplitude requirement, the reference clock inputs might need to be DC or
AC-coupled externally. For the best noise performance, the reference of the clock could be DC
or AC-coupled into the unused phase (SDn_REF_CLK) through the same source impedance as
the clock input (SDn_REF_CLK) in use.
Figure 53. Differential Reference Clock Input DC Requirements (External DC-Coupled)
SD
n_REF_CLK
SD
n_REF_CLK
Vmax < 800 mV
Vmin > 0 V
100 mV < Vcm < 400 mV
200 mV < Input Amplitude or Differential Peak < 800 mV
相關PDF資料
PDF描述
IDT70V5378S166BCI8 IC SRAM 576KBIT 166MHZ 256BGA
1-1734798-4 CONN HOUSING FPC 14POS R/A SMD
MPC8544EDVTANG IC MPU POWERQUICC III 783-FCBGA
IDT70V5388S100BG IC SRAM 1.125MBIT 100MHZ 272-BGA
2-84533-4 CONN FFC 24POS 1.25MM R/A PCB
相關代理商/技術參數
參數描述
MPC8377EVRAGDA 功能描述:微處理器 - MPU 8377 PBGA ST PbFr W/ENC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC8377EVRAGFA 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8377EVRAGGA 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8377EVRAJDA 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8377EVRAJF 功能描述:微處理器 - MPU PBGA W/ ENCR RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*