參數資料
型號: MQ83C154DCXXX-25P883D
廠商: ATMEL CORP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44
封裝: CERAMIC, QFP-44
文件頁數: 91/176頁
文件大?。?/td> 2962K
代理商: MQ83C154DCXXX-25P883D
21
2535J–AVR–08/10
ATtiny13
5.5.3
EECR – EEPROM Control Register
Bit 7 – Res: Reserved Bit
This bit is reserved for future use and will always read as 0 in ATtiny13. For compatibility with
future AVR devices, always write this bit to zero. After reading, mask out this bit.
Bit 6 – Res: Reserved Bit
This bit is reserved in the ATtiny13 and will always read as zero.
Bits 5:4 – EEPM[1:0]: EEPROM Programming Mode Bits
The EEPROM Programming mode bits setting defines which programming action that will be
triggered when writing EEPE. It is possible to program data in one atomic operation (erase the
old value and program the new value) or to split the Erase and Write operations in two different
operations. The Programming times for the different modes are shown in Table 5-1 on page 21.
While EEPE is set, any write to EEPMn will be ignored. During reset, the EEPMn bits will be
reset to 0b00 unless the EEPROM is busy programming.
Bit 3 – EERIE: EEPROM Ready Interrupt Enable
Writing EERIE to one enables the EEPROM Ready Interrupt if the I-bit in SREG is set. Writing
EERIE to zero disables the interrupt. The EEPROM Ready Interrupt generates a constant inter-
rupt when Non-volatile memory is ready for programming.
Bit 2 – EEMPE: EEPROM Master Program Enable
The EEMPE bit determines whether writing EEPE to one will have effect or not.
When EEMPE is set, setting EEPE within four clock cycles will program the EEPROM at the
selected address. If EEMPE is zero, setting EEPE will have no effect. When EEMPE has been
written to one by software, hardware clears the bit to zero after four clock cycles.
Bit 1 – EEPE: EEPROM Program Enable
The EEPROM Program Enable Signal EEPE is the programming enable signal to the EEPROM.
When EEPE is written, the EEPROM will be programmed according to the EEPMn bits setting.
The EEMPE bit must be written to one before a logical one is written to EEPE, otherwise no
EEPROM write takes place. When the write access time has elapsed, the EEPE bit is cleared by
hardware. When EEPE has been set, the CPU is halted for two cycles before the next instruction
is executed.
Bit
7
6
5
4
321
0
EEPM1
EEPM0
EERIE
EEMPE
EEPE
EERE
EECR
Read/Write
R
R/W
Initial Value
0
X
0
X
0
Table 5-1.
EEPROM Mode Bits
EEPM1
EEPM0
Programming
Time
Operation
0
3.4 ms
Erase and Write in one operation (Atomic Operation)
0
1
1.8 ms
Erase Only
1
0
1.8 ms
Write Only
1
Reserved for future use
相關PDF資料
PDF描述
MR80C52EXXX-25:RD 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44
MIP7365-450F17I 64-BIT, 450 MHz, MICROPROCESSOR, CQFP208
MIP7365-450B1M 64-BIT, 450 MHz, MICROPROCESSOR, PBGA256
MK1574-01BSITR 1574 SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16
MK1574-01ASTR 1574 SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16
相關代理商/技術參數
參數描述
MQ83C154-L16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ83C154T-12 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ83C154T-16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ83C154T-20 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ83C154T-25 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller