參數資料
型號： MR83C154XXX-25/883D
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44
封裝： LCC-44
文件頁數： 129/141頁
文件大小： 7628K
代理商： MR83C154XXX-25/883D
58
2486AA–AVR–02/2013
ATmega8(L)
Special Function IO
Register – SFIOR
Bit 2 – PUD: Pull-up Disable
When this bit is written to one, the pull-ups in the I/O ports are disabled even if the DDxn and
PORTxn Registers are configured to enable the pull-ups ({DDxn, PORTxn} = 0b01). See “Con-
figuring the Pin” on page 52 for more details about this feature.
Alternate Functions of
Port B
The Port B pins with alternate functions are shown in Table 22.
The alternate pin configuration is as follows:
XTAL2/TOSC2 – Port B, Bit 7
XTAL2: Chip clock Oscillator pin 2. Used as clock pin for crystal Oscillator or Low-frequency
crystal Oscillator. When used as a clock pin, the pin can not be used as an I/O pin.
TOSC2: Timer Oscillator pin 2. Used only if internal calibrated RC Oscillator is selected as chip
clock source, and the asynchronous timer is enabled by the correct setting in ASSR. When the
AS2 bit in ASSR is set (one) to enable asynchronous clocking of Timer/Counter2, pin PB7 is dis-
connected from the port, and becomes the inverting output of the Oscillator amplifier. In this
mode, a crystal Oscillator is connected to this pin, and the pin cannot be used as an I/O pin.
If PB7 is used as a clock pin, DDB7, PORTB7 and PINB7 will all read 0.
XTAL1/TOSC1 – Port B, Bit 6
XTAL1: Chip clock Oscillator pin 1. Used for all chip clock sources except internal calibrated RC
Oscillator. When used as a clock pin, the pin can not be used as an I/O pin.
TOSC1: Timer Oscillator pin 1. Used only if internal calibrated RC Oscillator is selected as chip
clock source, and the asynchronous timer is enabled by the correct setting in ASSR. When the
AS2 bit in ASSR is set (one) to enable asynchronous clocking of Timer/Counter2, pin PB6 is dis-
connected from the port, and becomes the input of the inverting Oscillator amplifier. In this
mode, a crystal Oscillator is connected to this pin, and the pin can not be used as an I/O pin.
If PB6 is used as a clock pin, DDB6, PORTB6 and PINB6 will all read 0.
Bit
7
6
5
4
3
2
1
0
ACME
PUD
PSR2
PSR10
SFIOR
Read/Write
R
R/W
Initial Value
0
Table 22. Port B Pins Alternate Functions
Port Pin
Alternate Functions
PB7
XTAL2 (
Chip Clock Oscillator pin 2)
TOSC2 (
Timer Oscillator pin 2)
PB6
XTAL1 (
Chip Clock Oscillator pin 1 or External clock input)
TOSC1 (
Timer Oscillator pin 1)
PB5
SCK (SPI Bus Master clock Input)
PB4
MISO (SPI Bus Master Input/Slave Output)
PB3
MOSI (SPI Bus Master Output/Slave Input)
OC2 (Timer/Counter2 Output Compare Match Output)
PB2
SS (SPI Bus Master Slave select)
OC1B (Timer/Counter1 Output Compare Match B Output)
PB1
OC1A (Timer/Counter1 Output Compare Match A Output)
PB0
ICP1 (Timer/Counter1 Input Capture Pin)
相關PDF資料
PDF描述
MD80C32E-16/883 8-BIT, 16 MHz, MICROCONTROLLER, CDIP40
MC80C52EXXX-25/883:D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CDIP40
MR80C52EXXX-12/883:R 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44
MC80C52XXX-16SHXXX:D 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40
MQ80C52TXXX-30SBR 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CQFP44
相關代理商/技術參數
參數描述
MR850 功能描述:整流器 3.0 Amp 50 Volt 150ns RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
MR850 _AY _10001 制造商:PanJit Touch Screens 功能描述:
MR850 R0 制造商:SKMI/Taiwan 功能描述:Diode Switching 50V 3A 2-Pin DO-201AD T/R
MR850_ R2 _10001 制造商:PanJit Touch Screens 功能描述:
MR850_09 制造商:PANJIT 制造商全稱:Pan Jit International Inc. 功能描述:SOFT RECOVERY, FAST SWITCHING PLASTIC RECTIFIER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*