- 您現在的位置：買賣IC網 > PDF目錄68018 > MSP53C691PM (TEXAS INSTRUMENTS INC) 8-BIT, 12.32 MHz, MIXED DSP, PQFP64 PDF資料下載
參數資料
| 型號： | MSP53C691PM |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | 8-BIT, 12.32 MHz, MIXED DSP, PQFP64 |
| 封裝： | PLASTIC, QFP-64 |
| 文件頁數： | 11/14頁 |
| 文件大小： | 203K |
| 代理商： | MSP53C691PM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁
MSP53C691
MIXED-SIGNAL PROCESSOR
SPSS030A – DECEMBER 2000 – REVISED FEBRUARY 2001
6
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
Master
MSP53C691
INRDY
OUTRDY
DATA (0–7)
8
4.7 k
4.7 k
4.7 k
VDD
100 k
(each)
VDD
RESET
R/W
STROBE
NOTE: STROBE:
Active low strobe signal from microcontroller
R/W:
Read/write signal from microcontroller
RESET
Active low reset signal from microcontroller.
INRDY:
Active low indicates that the MSP53C691 is ready to accept data.
OUTRDY:
Active low indicates that the MSP53C691 is ready to send data.
DATA0–DATA7
Data bits 0 through 7
PD4–PD7
General-purpose I/O bus
DACP
Output to speaker/amplifier
DACM
Output to speaker/amplifier
Figure 2. MSP53C691 Interfacing Diagram—8-Bit Mode
read operation by the master
The process for the read operation by the master is the same in either 4-bit or 8-bit mode. The read operation
by the master happens when the slave wants to send something to the master. The read process is initiated
by the slave by pulling OUTRDY low when it is ready.
The following events take place during the read operation:
D The MSP53C691 puts the data to be sent to the master on the internal bus.
D The MSP53C691 sets OUTRDY low to indicate that it is ready to send data to the microcontroller.
D The microcontroller sets R/W high to indicate a read operation.
D The microcontroller sets STROBE low. The data is available on the external data-bus at this point.
D The microcontroller reads the data from the bus.
D The microcontroller sets STROBE high. The MSP53C691 also pulls OUTRDY high at the rising edge of
STROBE.
D The data is taken from the external data-bus after STROBE goes high.
The microcontroller should latch or read in the data while STROBE is low. When the microcontroller sets
STROBE high, the MSP53C691 sets OUTRDY high to indicate that the data has been successfully transferred.
Figure 3 shows the sequence of events of the read operation.
相關PDF資料 |
PDF描述 |
|---|---|
| MSU2964C16-YYYQ | 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP44 |
| MSU2964C16-YYYJ | 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQCC44 |
| MSU2964C40 | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, UUC45 |
| MSU2964C16-YYYP | 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDIP40 |
| MSU2964C25-YYYP | 8-BIT, FLASH, 25 MHz, MICROCONTROLLER, PDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSP540 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:5 Amp Schottky Rectifier |
| MSP545 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:5 Amp Schottky Rectifier |
| MSP57600 | 制造商:Amphenol Corporation 功能描述: |
| MSP58C049BPJM | 制造商:Texas Instruments 功能描述: |
| MSP58C050BPJM | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。