- 您現在的位置：買賣IC網 > PDF目錄383642 > MT8931B (Mitel Networks Corporation) () PDF資料下載
參數資料
| 型號： | MT8931B |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | () |
| 中文描述： | （） |
| 文件頁數： | 17/29頁 |
| 文件大?。?/td> | 277K |
| 代理商： | MT8931B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Application Note
MSAN-141
A-217
Figure 15 - Controllerless Mode Functional Timing
Note:
F0b
HALF
MFR
M/S
MCH (NT)
MCH (TE)
M
S
M
S
Q-Bit
Q-Bit
Q-Bit
Q-Bit
In the controllerless mode, the parallel bus has direct
connection to the C-channel control and status
registers for either the TE or NT device. These
control/status pins allow the SNIC to be configured
using a discrete state machine or with manual
switches. All inputs/outputs to the control port will be
latched/refreshed by the SNIC on the falling edge of
the C4b clock midway through the system frame
pulse (F0b). Figure 15 shows the timing diagram
surrounding the structuring of the S- and Q-channels
in the NT controllerless mode.
In the controllerless mode, the SNIC can still be
controlled through the input C-channel on the system
(ST-BUS) interface. The structuring of the serial
control requires the P/SC pin to be tied to V
SS
, thus
rendering the remaining control pins as ”don’t cares”.
The option of disabling the ST-BUS channels is not
supported in the controllerless mode, therefore, all
input and output channels will be enabled.
5.0 TRANSMISSION PERFORMANCE
The transmission medium for the subscriber loop is a
four conductor configured as two twisted pairs.
Fig. 16 - I-V Characteristics of the Output Driver
To minimize the reflection of a propagating signal, a
100 ohm termination resistor is required in order to
match the characteristic impedance of the twisted
pair cable.
This terminating resistor is relevant to the
transmission line and is thus placed at both ends of
the transmit and receive pair (refer to Figures 7 to 9).
With the TE presenting a high impedance on both
Operating Point
20
1
0.75
0.95
1.25
15 mA
I
V
Figure 17 - NT Impedance Template (log-log scale)
2500
265
250
100
2
20
106
1000
Frequency (kHz)
Z
as output
相關PDF資料 |
PDF描述 |
|---|---|
| MT8930C-1 | SWITCH, ON-OFF, CHROM/BLK BTN; Switch function type:SPST Latching; Voltage, contact AC max:125V; Voltage, contact DC max:24V; Temp, op. max:85(degree C); Temp, op. min:-40(degree C); Diameter, panel cut-out:13.6mm; Length / Height, RoHS Compliant: Yes |
| MT8930C | Subscriber Network Interface Circuit(用戶網絡接口電路（提供點到點或點到多點數字傳送）) |
| MT8930 | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8930C | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8930CC | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8931BC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit |
| MT8931BE | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit |
| MT8931BP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Subscriber Network Interface Circuit |
| MT8931C | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Subscriber Network Interface Circuit |
| MT8931C-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
發布緊急采購，3分鐘左右您將得到回復。