- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9075B-1 (Mitel Networks Corporation) E1 Single Chip Transceiver PDF資料下載
參數資料
| 型號： | MT9075B-1 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | E1 Single Chip Transceiver |
| 中文描述： | 素E1單芯片收發器 |
| 文件頁數： | 13/78頁 |
| 文件大?。?/td> | 1008K |
| 代理商： | MT9075B-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
Preliminary Information
MT9075A
4-141
There are two CRC multiframe alignment algorithm
options selected by the AUTC control bit (address
11H, page 01H). When AUTC is zero and CSYN is
zero, automatic CRC-to-non-CRC interworking is
selected, if CRC-4 multiframe alignment is not found
in 400 msec, the status bit CRCIWK (page 03H,
address 10H) is set low and no further attempt to
achieve CRC-4 synchronization is made as long as
the
device
remains
synchronization. When AUTC is one and CSYN is
zero, a reframe will be initiated every 8 msec if the
MT9075A achieves terminal frame synchronization,
but fails to achieve CRC-4 synchronization.
in
terminal
frame
The control bit for transmit E bits (TE, bit 4 at
address 16H of page 01H) will have the same
function in both states of AUTC. That is, when CRC-4
synchronization is not achieved the state of the
transmit E-bits will be the same as the state of the TE
control bit. When CRC-4 synchronization is achieved
the transmit E-bits will function as per ITU-T G.704.
Table 4 outlines the recommended setting of the
TALM control bits of the MT9075A.
CAS Signalling Multiframing
The purpose of the signalling multiframing algorithm
is to provide a scheme that will allow the association
of a specific ABCD signalling nibble with the
appropriate PCM 30 channel. Time slot 16 is
reserved
for
the
communication
Associated Signalling (CAS) information (i.e., ABCD
signalling bits for up to 30 channels). Refer to ITU-T
G.704 and G.732 for more details on CAS
multiframing requirements.
of
Channel
A CAS signalling multiframe consists of 16 basic
frames (numbered 0 to 15), which results in a
multiframe repetition rate of 2 msec. It should be
noted that the boundaries of the signalling multiframe
may be completely distinct from those of the CRC-4
multiframe. CAS multiframe alignment is based on a
multiframe alignment signal (a 0000 bit sequence),
which occurs in the most significant nibble of time
slot 16 of basic frame 0 of the CAS multiframe. Bit 6
of this time slot is the multiframe alarm bit (usually
designated Y). When CAS multiframing is acquired
on the receive side, the transmit Y-bit is zero; when
CAS multiframing is not acquired, the transmit Y-bit is
one. Bits 5, 7 and 8 (usually designated X) are spare
bits and are normally set to one if not used.
Time slot 16 of the remaining 15 basic frames of the
CAS multiframe (i.e., basic frames 1 to 15) are
reserved for the ABCD signalling bits for the 30
payload channels. The most significant nibbles are
reserved for channels 1 to 15 and the least
significant nibbles are reserved for channels 16 to
30. That is, time slot 16 of basic frame 1 has ABCD
for channel 1 and 16, time slot 16 of basic frame 2
has ABCD for channel 2 and 17, through to time slot
16 of basic frame 15 has ABCD for channel 15 and
30.
MT9075A Access and Control
Register Access
The control and status of the MT9075A is achieved
through a non-multiplexed parallel microprocessor
port. The parallel port may be configured for
Motorola style control signals (by setting pin INT/
MOT low) or Intel style control signals (by setting pin
INT/MOT high).
The controlling microprocessor gains access to
specific registers of the MT9075A through a two step
process. First, writing to the internal Command/
Address Register (CAR) selects one of the 18 pages
of control and status registers (CAR address: AC4 =
0, AC3-AC0 = don't care, CAR data D7 - D0 = page
number). Second, each page has a maximum of 16
registers that are addressed on a read or write to a
non-CAR address (non-CAR: address AC4 = 1, AC3-
AC0 = register address, D7-D0 = data). Once a page
Table 4 - Transmit RAI setting for CRC to non CRC interworking with AUTC set low
SYNC
CRCSYN
CRCIWK
Recommended Transmit RAI setting
0
0
1
Set transmit RAI continuously low.
0
0
0
This state cannot exist with AUTC set low.
1
1
x
Set transmit RAI continuously high.
0
1
1
Transmit a flickering (0 to 1 to 0) RAI every 8 milliseconds.
0
1
0
The link is a CRC to non CRC link. Set transmit RAI to the appropriate
stable state (usually low).
相關PDF資料 |
PDF描述 |
|---|---|
| MT9075 | () |
| MT9076 | T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076AB | T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076 | T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器) |
| MT9079 | Advanced Controller for E1(先進的E1幀調節器和控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9075BL | 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 100MQFP - Trays |
| MT9075BL1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 100MQFP - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL E1 W/LIU 100MQFP 制造商:Microsemi Corporation 功能描述:IC TXRX SGL E1 W/LIU 100MQFP |
| MT9075BP | 制造商:Microsemi Corporation 功能描述: |
| MT9075BP1 | 制造商:Microsemi Corporation 功能描述:Single Chip Transceiver 1TX 1RX 2.048Mbps 68-Pin PLCC Tube 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 68PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:PB FREE E1 SINGLE CHIP TRANSCEIVER 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL E1 W/LIU 68PLCC 制造商:Microsemi Corporation 功能描述:IC TXRX SGL E1 W/LIU 68PLCC |
| MT9075BPR | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:E1 Single Chip Transceiver |
發布緊急采購，3分鐘左右您將得到回復。