參數資料
型號: MTB50P03HDLT4
廠商: MOTOROLA INC
元件分類: JFETs
英文描述: 50 A, 30 V, 0.03 ohm, P-CHANNEL, Si, POWER, MOSFET
文件頁數: 8/12頁
文件大?。?/td> 182K
代理商: MTB50P03HDLT4
MTB50P03HDL
5
Motorola TMOS Power MOSFET Transistor Device Data
QT, TOTAL GATE CHARGE (nC)
RG, GATE RESISTANCE (Ohms)
t,TIME
(ns)
V
DS
,DRAIN–T
O–SOURCE
VOL
TAGE
(VOL
TS)
V
GS
,GA
TE–T
O–SOURCE
VOL
TAGE
(VOL
TS)
Figure 8. Gate–To–Source and Drain–To–Source
Voltage versus Total Charge
110
10
100
1000
VDD = 30 V
ID = 50 A
VGS = 10 V
TJ = 25°C
tf
td(on)
td(off)
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
0
103050
60
80
20
40
3
6
2
0
1
4
5
30
25
20
15
5
10
0
QT
Q2
VGS
ID = 50 A
TJ = 25°C
VDS
Q3
Q1
70
tr
DRAIN–TO–SOURCE DIODE CHARACTERISTICS
The switching characteristics of a MOSFET body diode
are very important in systems using it as a freewheeling or
commutating diode. Of particular interest are the reverse re-
covery characteristics which play a major role in determining
switching losses, radiated noise, EMI and RFI.
System switching losses are largely due to the nature of
the body diode itself. The body diode is a minority carrier de-
vice, therefore it has a finite reverse recovery time, trr, due to
the storage of minority carrier charge, QRR, as shown in the
typical reverse recovery wave form of Figure 12. It is this
stored charge that, when cleared from the diode, passes
through a potential and defines an energy loss. Obviously,
repeatedly forcing the diode through reverse recovery further
increases switching losses. Therefore, one would like a
diode with short trr and low QRR specifications to minimize
these losses.
The abruptness of diode reverse recovery effects the
amount of radiated noise, voltage spikes, and current ring-
ing. The mechanisms at work are finite irremovable circuit
parasitic inductances and capacitances acted upon by high
di/dts. The diode’s negative di/dt during ta is directly con-
trolled by the device clearing the stored charge. However,
the positive di/dt during tb is an uncontrollable diode charac-
teristic and is usually the culprit that induces current ringing.
Therefore, when comparing diodes, the ratio of tb/ta serves
as a good indicator of recovery abruptness and thus gives a
comparative estimate of probable noise generated. A ratio of
1 is considered ideal and values less than 0.5 are considered
snappy.
Compared to Motorola standard cell density low voltage
MOSFETs, high cell density MOSFET diodes are faster
(shorter trr), have less stored charge and a softer reverse re-
covery characteristic. The softness advantage of the high
cell density diode means they can be forced through reverse
recovery at a higher di/dt than a standard cell MOSFET
diode without increasing the current ringing or the noise gen-
erated. In addition, power dissipation incurred from switching
the diode will be less due to the shorter recovery time and
lower switching losses.
I S
,SOURCE
CURRENT
(AMPS)
VSD, SOURCE–TO–DRAIN VOLTAGE (VOLTS)
Figure 10. Diode Forward Voltage versus Current
0
10
30
50
40
20
0.4
0.6
0.8
1.0
1.2
1.4
VGS = 0 V
TJ = 25°C
1.6
1.8
2.0
2.2
2.4
相關PDF資料
PDF描述
MTB52N06VLT4 52 A, 60 V, 0.025 ohm, N-CHANNEL, Si, POWER, MOSFET
MTB52N06VL 52 A, 60 V, 0.025 ohm, N-CHANNEL, Si, POWER, MOSFET
MTB52N06VLT4G 52 A, 60 V, 0.025 ohm, N-CHANNEL, Si, POWER, MOSFET
MTB52N06VT4 52 A, 60 V, 0.022 ohm, N-CHANNEL, Si, POWER, MOSFET
MTB60N05HDT4 60 A, 50 V, 0.014 ohm, N-CHANNEL, Si, POWER, MOSFET
相關代理商/技術參數
參數描述
MTB50P03HDLT4G 功能描述:MOSFET PFET D2PAK 30V 50A 25mOhm RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS(導通):0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube
MTB50SA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Full-Size (7.3mm or 4.7mm height)
MTB50SAM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Full-Size (7.3mm or 4.7mm height)
MTB50SAV 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Full-Size (7.3mm or 4.7mm height)
MTB50SAVM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Full-Size (7.3mm or 4.7mm height)