- 您現在的位置：買賣IC網 > PDF目錄45322 > MV80C51T-16D (TEMIC SEMICONDUCTORS) 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | MV80C51T-16D |
| 廠商： | TEMIC SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44 |
| 文件頁數： | 84/170頁 |
| 文件大小： | 4133K |
| 代理商： | MV80C51T-16D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁當前第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁
20
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
6.4
Starting
6.4.1
Starting from Reset
The internal reset is immediately asserted when a reset source goes active. The internal reset is kept asserted until
the reset source is released and the start-up sequence is completed. The start-up sequence includes three steps,
as follows.
1.
The first step after the reset source has been released consists of the device counting the reset start-up
time. The purpose of this reset start-up time is to ensure that supply voltage has reached sufficient levels.
The reset start-up time is counted using the internal 128 kHz oscillator. See Table 6-1 for details of reset
start-up time.
Note that the actual supply voltage is not monitored by the start-up logic. The device will count until the
reset start-up time has elapsed even if the device has reached sufficient supply voltage levels earlier.
2.
The second step is to count the oscillator start-up time, which ensures that the calibrated internal oscillator
has reached a stable state before it is used by the other parts of the system. The calibrated internal oscil-
lator needs to oscillate for a minimum number of cycles before it can be considered stable. See Table 6-1
for details of the oscillator start-up time.
3.
The last step before releasing the internal reset is to load the calibration and the configuration values from
the Non-Volatile Memory to configure the device properly. The configuration time is listed in Table 6-1.
Notes:
1. After powering up the device or after a reset the system clock is automatically set to calibrated internal 8 MHz oscil-
lator, divided by 8
6.4.2
Starting from Power-Down Mode
When waking up from Power-Down sleep mode, the supply voltage is assumed to be at a sufficient level and only
the oscillator start-up time is counted to ensure the stable operation of the oscillator. The oscillator start-up time is
counted on the selected main clock, and the start-up time depends on the clock selected. See Table 6-2 for details.
Notes:
1. The start-up time is measured in main clock oscillator cycles.
6.4.3
Starting from Idle / ADC Noise Reduction / Standby Mode
When waking up from Idle, ADC Noise Reduction or Standby Mode, the oscillator is already running and no oscilla-
tor start-up time is introduced.
The ADC is available in ATtiny5/10, only.
Table 6-1.
Start-up Times when Using the Internal Calibrated Oscillator
Reset
Oscillator
Configuration
Total start-up time
64 ms
6 cycles
21 cycles
64 ms + 6 oscillator cycles + 21 system clock cycles (1)
Table 6-2.
Start-up Time from Power-Down Sleep Mode.
Oscillator start-up time
Total start-up time
6 cycles
6 oscillator cycles (1)
相關PDF資料 |
PDF描述 |
|---|---|
| MS80C51T-20R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQCC44 |
| MF180C31-25D | 8-BIT, 25 MHz, MICROCONTROLLER, PQFP44 |
| MF180C51T-25R | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP44 |
| MS80C51C-36R | 8-BIT, MROM, 36 MHz, MICROCONTROLLER, PQCC44 |
| MF280C51C-12R | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MV8102 | 功能描述:標準LED-通孔 T-1 3/4 RED CLR 20DG RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| MV8102 | 制造商:Fairchild Semiconductor Corporation 功能描述:LED ALGAAS SUPERBRIGHT RED |
| MV8102 | 制造商:Fairchild Semiconductor Corporation 功能描述:LED LAMP |
| MV8103 | 功能描述:標準LED-通孔 T-1 3/4 RED CLR 20DG RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| MV8104 | 功能描述:標準LED-通孔 T-1 3/4 RED CLR 20DG RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。