NB6L16
http://onsemi.com
7
Table 7. AC CHARACTERISTICS VCC = 0 V; VEE = 3.465 V to 2.375 V or VCC = 2.375 V to 3.465 V; VEE = 0 V (Note 24) Symbol
Characteristic
40°C
25°C
85°C
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
VOUTPP
Output Voltage Amplitude
fin < 3 GHz
fin < 6 GHz
500
270
700
350
500
270
700
350
500
270
700
300
mV
fDATA
Maximum Operating Data Rate
6
Gb/s
tPLH,
tPHL
Propagation Delay to
Output Differential @ 1 GHz
80
130
180
80
130
180
85
135
185
ps
tSKEW
Duty Cycle Skew (Note
25)DevicetoDevice Skew
3
30
25
60
3
30
25
60
3
30
25
60
ps
tJITTER
RMS Random Clock Jitter
fin < 6 GHz
PeaktoPeak Data Dependent JItter
fin < 6 Gb/s
0.2
2
1
12
0.2
2
1
12
0.2
2
1
12
ps
VINPP
Input Voltage Swing / Sensitivity
(Differential Configuration) (Note
28)
75
700
2500
75
700
2500
75
700
2500
mV
tr
tf
Output Rise/Fall Times
Q, Q
(20% 80%)
30
70
120
30
70
120
30
70
120
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
24.Measured using a 800 mV source, 50% duty cycle clock source. All loading with 50 W to VCC. Input edge rates 40 ps (20% 80%).
25.See Figure 9 tskew = |tPLH tPHL| for a nominal 50% differential clock input waveform. Skew is measured between outputs under identical transitions and conditions @ 1 GHz.
26.Additive RMS jitter with 50% duty cycle clock signal at 6 GHz.
27.Additive PeaktoPeak data dependent jitter with NRZ PRBS 2231 data rate at 6 Gb/s.
28.VINPP(max) cannot exceed VCC VEE. (Applicable only when VCC VEE < 2500 mV). Input voltage swing is a singleended measurement
operating in the differential mode.
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
1
2
3
4
5
678
OUTPUT
VOL
TAGE
AMPLITUDE
(V)
INPUT CLOCK FREQUENCY (GHz)
Figure 2. Output Voltage Amplitude (VOUTPP)
versus Input Clock Frequency (fIN) and
Temperature at VCC VEE = 3.3 V
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
12
34
5
6
7
8
INPUT CLOCK FREQUENCY (GHz)
Figure 3. Output Voltage Amplitude (VOUTPP)
versus Input Clock Frequency (fIN) and
Temperature at VCC VEE = 2.5 V
OUTPUT
VOL
TAGE
AMPLITUDE
(V)
85°C
40°C
25°C
40°C
25°C
85°C