參數資料
型號： NCN6000DTBR2
廠商： ON Semiconductor
文件頁數： 26/36頁
文件大?。?/td> 0K
描述： IC INTERFACE SMART CARD 20TSSOP
產品變化通告： Product Obsolescence 01/Jul/2009
標準包裝： 1
應用： ATM 終端，氣泵，ISM
接口： 微控制器
電源電壓： 2.7 V ~ 6 V
封裝/外殼： 20-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 20-TSSOP
包裝： 標準包裝
安裝類型： 表面貼裝
產品目錄頁面： 1131 (CN2011-ZH PDF)
其它名稱： NCN6000DTBR2OSDKR
NCN6000
http://onsemi.com
32
Printed Circuit Board Layout
Since the NCN6000 carries high speed currents together
with high frequency clock, the printed circuit board must be
carefully designed to avoid the risk of uncontrolled
operation of the interface.
A typical singlesided PCB layout is provided in
Figure 34 highlighting the ground technique.
The card socket uses a low cost ISO only version, all the
parts being located on the Component side. Connector J3
makes reference to the microcontroller used by the final
application. Of course, the connector is not necessary and
standard copper tracks might be used to connect the MPU to
the NCN6000 interface chip.
2335 mis (60 mm)
2760
mis
(70
mm)
U1
NCN6000
SMARTCARD ISO CONTACTS
MPU
V
supply
+V
bat
C4
CLK
RST
GROUND
C8
I/O
VPP
GND
Figure 34. Typical Single Sided Printed Circuit Board Layout
Application Note
A partial schematic diagram of the demo board designed
to support the NCN6000 applications is depicted in
Figure 35. This schematic diagram highlights the interface
between the microcontroller and the Smart Card, leaving
aside the peripherals used to control the MPU.
Conclusion
From a practical stand point, the CRD_VCC output
capacitor has been split into two 6.8
mF/10 V/X7R, one
being located as close as possible across pins 13 and 17 of
the NCN6000, the second one being located close by the
smart card physical connector. On the other hand, care has
been observed to minimize the cross coupling between the
clock signals (both Input and CRD_CLK) and the other
signals presents on the board.
The microcontroller holds the software necessary to
program the NCN6000, together with the code handling the
T0
operation.
Provisions
are
made
to
provide
a
communication link with an external computer by using the
RS232 standard port.
Due to the Chip Select signal, several NCN6000 can share
a common data bus as depicted in Figure 36. In this example,
two interfaces are connected to a single MPU, the CS pins
being controlled by two different signals.
相關PDF資料
PDF描述
DS8113-RNG+ IC INTERFACE SMART CARD 28-SOIC
MAX1563ETC+ IC CURR-LIM SW SNGL PROG 12-TQFN
MAX6817EUT+T IC DEBOUNCER SWITCH DUAL SOT23-6
D38999/20MD18PN CONN RCPT 18POS WALL MNT W/PINS
D38999/26FC8PB CONN PLUG 8POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
NCN6000DTBR2G 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
NCN6001 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs
NCN6001/D 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC
NCN6001_06 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC
NCN6001_0610 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*