參數資料
型號: NCP1601BDR2G
廠商: ON Semiconductor
文件頁數: 3/19頁
文件大小: 257K
描述: IC PFC CTRL CRM/TRANSITION 8SOIC
產品變化通告: NCP1601BDR2G Discontinuation 11/May/2012
標準包裝: 1
模式: 臨界傳導(CRM),間歇式(轉換)
頻率 - 開關: 58kHz
電流 - 啟動: 17µA
電源電壓: 9.6 V ~ 18 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 8-SOICN
包裝: 剪切帶 (CT)
其它名稱: NCP1601BDR2GOSCT
NCP1601A, NCP1601B
http://onsemi.com
3
PIN FUNCTION DESCRIPTION
Pin
Symbol
Function
Function
1
FB
Feedback /
Shutdown
This pin receives a current I
FB
which is proportional to the PFC circuit output voltage. The current is
for the output regulation, output Overvoltage Protection (OVP), and output undervoltage protection
(UVP).
When I
FB
goes above 107% I
ref
, OVP is activated and the Drive Output is disabled.
When I
FB
goes below 8% I
ref
, the device enters a low- -current consumption shutdown mode.
2
V
control
Control
The voltage of this pin V
control
directly controls the input impedance and hence the power factor of
the circuit. This pin is connected to an external capacitor to limit the control voltage V
control
band-
width typically below 20 Hz to achieve Power Factor Correction.
3
Ramp
Ramp
This pin is connected to an external capacitor to set a ramp signal. The capacitor value directly
affects the input impedance of the PFC circuit and hence the maximum input power.
4
CS
Current Sense
This pin sources a current I
S
which depends on the inductor current and an offset voltage. The
current is for Overcurrent Protection (OCP) and zero current detection.
When I
S
is above 200 mA, OCP is activated and the Drive Output is disabled.
When I
S
is below 14 mA, the circuit detects a zero current. This information is used by the on- -time
modulation arrangement and by the oscillator block.
5
Osc
Oscillator /
Synchronization
In oscillator mode, this pin is connected to an external capacitor to set the oscillator frequency of
the DCM operation.
In synchronization mode, this pin is connected to an external driving signal. The positive edge of the
drive output is synchronized to the negative edge of the external signal in DCM operation.
If the inductor current is non- -zero at the end of a switching period, the output drive is not allowed to
turn on. CCM operation is prohibited. Instead, the circuit operates in CRM in this case.
6
GND
The IC ground
- -
7
Drv
Drive Output
This pin provides an output to an external MOSFET.
8
V
CC
Supply Voltage
This pin is the positive supply of the device. The operating range is between 9 V and 18 V with
UVLO start threshold 13.75 V for NCP1601A and 10.5 V for NCP1601B.
相關PDF資料
PDF描述
NCP1603D100R2G IC CTLR PFC/PWM COMBO 16-SOIC
NCP1605DR2G IC PFC CONTROLLER CCM/DCM 16SOIC
NCP1606BDR2G IC POWER FACTOR CONTROLLER 8SOIC
NCP1607BDR2G IC PFC CONTROLLER CRM 8SOIC
NCP1611BDR2G IC PFC CTLR HE ENHANCED 8-SOIC
相關代理商/技術參數
參數描述
NCP1601BP 功能描述:功率因數校正 IC Fixed Frequency RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
NCP1601BPG 功能描述:功率因數校正 IC Fixed Frequency DCM/CRM PFC RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
NCP1603D100R2 功能描述:功率因數校正 IC High Voltage Startup RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
NCP1603D100R2G 功能描述:功率因數校正 IC ANA PFC/PWM COMBO CONTROL RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
NCP1605ADR2G 功能描述:功率因數校正 IC ENHANCED PFC CNTRLER RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel