- 您現在的位置：買賣IC網 > Datasheet目錄45 > NCT75MNR2G (ON Semiconductor)IC SENSOR TEMP DGTL 8DFN Datasheet資料下載
參數資料
| 型號： | NCT75MNR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 181K |
| 描述： | IC SENSOR TEMP DGTL 8DFN |
| 標準包裝： | 3,000 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±3°C |
| 拓?fù)洌?/td> | ADC（三角積分型），控制邏輯，寄存器庫 |
| 輸出類型： | 2 線串行，I²C?/SMBUS? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-DFN（2x2） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
NCT75
http://onsemi.com
8
Serial Interface
Control of the NCT75 is carried out via the SMBus/I
2
C
compatible serial interface. The NCT75 is connected to this
bus as a slave device, under the control of a master device.
Serial Bus Address
Control of the NCT75 is carried out via the serial bus. The
NCT75 is connected to this bus as a slave device under the
control of a master device. The NCT75 has a 7-bit serial
address. The four MSBs are fixed and set to 1001 while the
3 LSBs can be configured by the user using pins 5, 6 and 7
(A2, A1 and A0). Each of these pins can be configured in one
of two ways low or high. This gives eight different address
options listed in Table 14 below. The state of these pins is
continually sampled and so can be changed after power up.
Table 14. SERIAL BUS ADDRESS OPTIONS
MSBs
LSBs
Address
A6
A5
A4
A3
A2
A1
A0
Hex
1
0
0
1
0
0
0
0x48
1
0
0
1
0
0
1
0x49
1
0
0
1
0
1
0
0x4A
1
0
0
1
0
1
1
0x4B
1
0
0
1
1
0
0
0x4C
1
0
0
1
1
0
1
0x4D
1
0
0
1
1
1
0
0x4E
1
0
0
1
1
1
1
0x4F
The NCT75 also features a SMBus/I
2
C timeout function
whereby the SMBus/I
2
C interface times out after 22.5 ms of
no activity on the SDA line. After this time, the NCT75
resets the SDA line back to its idle state (high impedance)
and waits for the next start condition.
The serial bus protocol operates as follows:
1. The master initiates data transfer by establishing
a start condition, defined as a high to low
transition on the serial data line SDA, while the
serial clock line SCL remains high. This indicates
that an address/data stream is going to follow. All
slave peripherals connected to the serial bus
respond to the start condition and shift in the next
eight bits, consisting of a 7-bit address (MSB first)
plus a read/write (R/W
) bit, which deternimes the
direction of the data transfer i.e. whether data is
written to, or read from, the slave device. The
peripheral with the address corresponding to the
transmitted address responds by pulling the data
line low during the low period before the ninth
clock pulse, known as the acknowledge bit. All
other devices on the bus now remain idle while the
selected device waits for data to be read from or
written to it. If the R/W
bit is a zero then the
master writes to the slave device. If the R/W
bit is
a one then the master reads from the slave device.
2. Data is sent over the serial bus in sequences of
nine clock pulses, eight bits of data followed by an
acknowledge bit from the receiver of data.
Transitions on the data line must occur during the
low period of the clock signal and remain stable
during the high period, since a low-to-high
transition when the clock is high can be interpreted
as a stop signal.
3. When all data bytes have been read or written,
stop conditions are established. In write mode, the
master pulls the data line high during the tenth
clock pulse to assert a stop condition. In read
mode, the master overrides the acknowledge bit by
pulling the data line high during the low period
before the ninth clock pulse. This is known as no
acknowledge. The master takes the data line low
during the low period before the tenth clock pulse,
then high during the tenth clock pulse to assert a
stop condition.
Any number of bytes of data can be transferred over the
serial bus in one operation. However, it is not possible to mix
read and write in one operation because the type of operation
is determined at the beginning and cannot subsequently be
changed without starting a new operation.
Writing Data
There are two types of writes used in the NCT75:
Setting up the Address Pointer Register for a Register
Read
To read data from a particular register, the address pointer
register must hold the address of the register being read. To
configure the address pointer register a single write
operation (shown in Figure 5). It consists of the device
address followed by the address being written to the address
pointer register. This will then be followed by a read
operation.
Writing Data to a Register
Due to the different size registers used by the NCT75,
there are two types of write operations. One is for the 8 bit
wide configuration register and the other for the 16 bit wide
limit registers.
Figure 6 shows the sequence required to write to the
configuration register. It consists of the device address, the
data register being written to and the data being written the
selected register.
The two temperature limit registers (T
HYST
and T
OS
) are
16 bits wide and require two data bytes to be written to these
registers. This sequence is shown in Figure 7. It consists of
the device address, the data register being written to and the
two data byes being written to the selected register.
相關PDF資料 |
PDF描述 |
|---|---|
| NCV8881PWR2G | IC REG TRPL BUCK/LINEAR 16SOIC |
| NE1617ADS,112 | IC TEMP MONITOR 16SSOP |
| NE1619DS,118 | IC TEMP MONITOR 16SSOP |
| NIS5112D1R2G | IC ELECTRONIC FUSE HOTSWAP 8SOIC |
| NIS5132MN2TXG | IC ELECTRONIC FUSE 12V 10DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCT7717U TR | 制造商:Nuvoton Technology Corp 功能描述:SMBUS INTERFACE TEMP. SENSOR W 制造商:Nuvoton Technology Corp 功能描述:IC SMBUS TEMP SENSOR 8MSOP |
| NCT7718W TR | 制造商:Nuvoton Technology Corp 功能描述:IC SMBUS TEMP SENSOR 8MSOP |
| NCT7802Y | 制造商:Nuvoton Technology Corp 功能描述: |
| NCT7904D | 制造商:Nuvoton Technology Corp 功能描述:IC H/W MONITOR |
| NCT80DBR2G | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。