參數資料
型號： P0300SCRP
英文描述： MCU CMOS 44 LD 20MHZ 8K OTP, -40C to +125C, 44-MQFP, TRAY
中文描述： SIDAC的| 40V的五（公報）最大| 800mA的我（縣）|的DO - 214AA
文件頁數： 69/161頁
文件大?。?/td> 986K
代理商： P0300SCRP
SIDACtor
Data Book
Secondary Protection
Teccor Electronics
(972) 580-7777
3 - 29
R
$
Secondary Protectors
Secondary protectors are adjunct devices (they can be either stand alone units or
integrated into strip protectors and UPS
’
) used to enhance the protection level of
customer premise equipment (CPE). Due to the inadequate level of protection being
designed into CPE, secondary protectors are often required to help prevent premature
failure of equipment that is exposed to environmental hazards (Figure 3-31).
Protection Requirements
Secondary protectors should be able to withstand over-voltages that can exceed 800V
and surge currents of up to 100A. In Figure 3-32, the SIDACtor was chosen because
the associated peak pulse current (I
PP
) is great enough to withstand the lightning
immunity tests of FCC Part 68 without the additional use of series line impedance.
Likewise, the fuse in Figure 3-32 was chosen because the amps
2
time (I
2
t) rating is
large enough to withstand the lightning immunity tests of FCC Part 68, but small
enough to pass UL power cross conditions.
Applicable Regulatory Requirements
UL 497A
Secondary Protection Reference Circuit
Figure 3-32 is an example of an interface design for a secondary protector. The
P3203AB SIDACtor is used because the peak off-state voltage (V
DRM
) is greater than
the potential of a Type B ringer signal superimposed on the POTS (plain old telephone
service) battery.
150V
RMS
√
2 + 56.6Vpk = 268.8Vpk
Coordination between the station protector and the secondary protector occurs due to
the line impedance between the two devices (Figure 3-31). The line impedance helps
ensure that the primary protector will begin to conduct while the secondary protector
limits any of the let through voltage to within the V
S
rating of the SIDACtor.
相關PDF資料
PDF描述
P0602ABRP SIDAC|40V V(BO) MAX|800MA I(S)|TO-220VAR
P0602AC SIDAC|40V V(BO) MAX|800MA I(S)|TO-220VAR
P0602ACRP SIDAC|40V V(BO) MAX|800MA I(S)|TO-220VAR
P0640EA SIDAC|77V V(BO) MAX|800MA I(S)|TO-92VAR
P0640EARP1 18LD 4MHZ 1K EPRM/128 EEPROM, 0C to +70C, 18-SOIC 300mil, TUBE
相關代理商/技術參數
參數描述
P0300SD 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:High Surge Current (D-rated) SIDACtor Device
P0300Z 制造商:TECCOR 制造商全稱:TECCOR 功能描述:solid state crowbar devices
P0300ZA 功能描述:硅對稱二端開關元件 4Chp 25V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P0300ZB 功能描述:硅對稱二端開關元件 4Chp 25V 100A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P0300ZC 功能描述:硅對稱二端開關元件 4Chp 25V 500A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*