參數資料
型號： P1500ECRP2
英文描述： MCU CMOS 18 LD 4MHZ .5K FLASH, 0C to +70C, 18-PDIP, TUBE
中文描述： SIDAC的| 180V五（公報）最大| 800mA的我（縣）|對92VAR
文件頁數： 132/161頁
文件大小： 986K
代理商： P1500ECRP2
Soldering Recommendations
SIDACtor
Data Book
5 - 16
Teccor Electronics
(972) 580-7777
$
Overview
When placing surface mount components, a good solder bond is critical because:
1. The solder provides a thermal path in which heat is dissipated from the
packaged silicon to the rest of the board.
2. A good bond is less subject to thermal fatiguing and results in improved component
reliability.
Reflow Soldering
The preferred technique for mounting the DO-214 package is to reflow-solder the
device onto a PCB - printed circuit board. (Figure 5-6).
Figure 5-6 Reflow Soldering Procedure
For reliable connections, the PCB should first be screen printed with a solder paste or
fluxed with a reliable solution that is easily removed such as Alpha 5003 diluted with
benzyl alcohol. If using a flux, the PCB should be allowed to dry to touch at room
temperature (or in a 70
°
C oven) prior to placing the components on the solder pads.
Relying on the adhesive nature of the solder paste or flux to prevent the devices from
moving prior to reflow, components should be placed with either a vacuum pencil or
automated pick and place machine.
With the components in place, the PCB should be heated to a point where the solder
on the pads begins to flow. This is typically done on a conveyor belt which first
transports the PCB through a pre-heating zone. The pre-heating zone is necessary in
order to reduce thermal shock and prevent damage to the devices being soldered, and
should be limited to a maximum temperature of 165
°
C for 10 seconds.
After pre-heating, the PCB goes to a vapor zone. The vapor zone is obtained by
heating an inactive fluid to its boiling point while using a vapor lock to regulate the
chamber temperature. This temperature is typically 215
°
C, but for temperatures in
1. Screen print solder paste
(or flux)
2. Place component
(allow flux to dry)
3. Reflow solder
相關PDF資料
PDF描述
P1500SARP MCU CMOS 18 LD 4MHZ .5K FLASH, -40C to +85C, 18-SOIC 300mil, TUBE
P1500SBRP MCU CMOS 18 LD 10MHZ .5K FLASH, -40C to +85C, 18-PDIP, TUBE
P1500SCRP MCU CMOS 18 LD LOW PWR, 0C to +70C, 18-SOIC 300mil, TUBE
P1602ABRP MCU CMOS 18 LD LOW PWR, -40C to +85C, 18-PDIP, TUBE
P1602AC MCU CMOS 18 LD LOW PWR, -40C to +85C, 18-SOIC 300mil, TUBE
相關代理商/技術參數
參數描述
P1500G_LRP 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:Teccor㈢ brand Protection Thyristors
P1500GALRP 功能描述:硅對稱二端開關元件 140V 50A DO15 SIDACtor Bi RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1500GBLRP 功能描述:硅對稱二端開關元件 140V 80A DO15 SIDACtor Bi RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1500GTL 制造商:SEMIKRON 制造商全稱:Semikron International 功能描述:Standard silicon rectifier diodes
P1500JTL 制造商:SEMIKRON 制造商全稱:Semikron International 功能描述:Standard silicon rectifier diodes
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*