參數資料
型號: P1602ACRP
英文描述: MCU CMOS 18 LD LOW PWR, 0C to +70C, 18-SOIC 300mil, T/R
中文描述: SIDAC的| 95V V(下公報)最大| 800mA的我(縣)|對220VAR
文件頁數: 130/161頁
文件大?。?/td> 986K
代理商: P1602ACRP
PCB Layout
SIDACtor
Data Book
5 - 14
Teccor Electronics
(972) 580-7777
The minimum width and thickness of conductors on a PCB is determined primarily by
the current-carrying capacity required. This current carrying capacity is limited by the
allowable temperature rise of the etched copper conductor. An adjacent ground or
power layer can significantly reduce this temperature rise. A single ground plane can
generally raise the allowed current by 50 percent. An easy approximation can be
generated by starting with Figure 5-4 to calculate the conductor cross sectional area
required. Once this has been done, Figure 5-5 converts the cross sectional area to the
required conductor width dependent on the copper foil thickness of the trace.
Figure 5-5 Conductor Width vs. Area
Trace Separation
Because Tip and Ring traces are subjected to transient conditions, they should be
routed towards the edge of the PCB away from sensitive areas, and should maintain a
minimum separation of 2.5mm between themselves and other traces. A good rule of
thumb for separation of non-coated top layer traces is to maintain spacing equal to
.010mm per volt.
Grounding
Although often overlooked, grounding is a very important design consideration when
laying out a protection interface circuit. To optimize its effectiveness, several things
should be considered.
The first is that a large copper plane should be provided using a grid pattern for the
ground reference point.
Next, it should be decided if a single point or a multi point grounding scheme is to be
used. A single-point (also called centralized) grounding scheme is used for circuit
dimensions smaller than one-tenth of a wavelength (
λ
= 300,000/F
kHz
) and a multi
point (also called distributed) grounding scheme is used for circuit trace lengths
0
.350
.300
.250
.030
.050
.070
.100
.150
.200
.010
.020
.005
.001
0
1
10
20
100 150
300
400
500
600
700
Conductor Cross-Section Area (sq mils)
5
30 50 70
200
250
C
0
"
7
0
0
0
2
t
o
2
"
4
1
0
0
2
t
o
1
(2oz/ft2 .0028"
(3oz/ft2) .0042"
相關PDF資料
PDF描述
P1800SARP SIDAC|220V V(BO) MAX|800MA I(S)|DO-214AA
P1800SBRP SIDAC|220V V(BO) MAX|800MA I(S)|DO-214AA
P1800SCRP SIDAC|220V V(BO) MAX|800MA I(S)|DO-214AA
P1803AA SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR
P1803AARP SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR
相關代理商/技術參數
參數描述
P160-2B 功能描述:手工工具 MANUAL WIREWRAP TOOL RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool
P1602CA 功能描述:硅對稱二端開關元件 65/130V 50A SIDACtor Bi RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流(在 VDRM IDRM 下): 保持電流(Ih 最大值):50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1602CAL 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:gas plasma arresters-package dimensions/specifications
P1602CALRP 功能描述:硅對稱二端開關元件 500A 65/130V RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流(在 VDRM IDRM 下): 保持電流(Ih 最大值):50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1602CARP 功能描述:硅對稱二端開關元件 500A 65/130V RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流(在 VDRM IDRM 下): 保持電流(Ih 最大值):50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA