- 您現在的位置：買賣IC網 > PDF目錄367729 > P83C592FFA (NXP SEMICONDUCTORS) Single-chip 8-bit microcontroller with CAN controller(帶CAN控制器的單片8位微控制器) PDF資料下載
參數資料
| 型號： | P83C592FFA |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Single-chip 8-bit microcontroller with CAN controller(帶CAN控制器的單片8位微控制器) |
| 中文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQCC68 |
| 封裝： | PLASTIC, SOT-168-3, MO-047AE, LCC-68 |
| 文件頁數： | 19/108頁 |
| 文件大?。?/td> | 650K |
| 代理商： | P83C592FFA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
1996 Jun 27
19
Philips Semiconductors
Product specification
8-bit microcontroller with on-chip CAN
P8xC592
10.1
ADC Control register (ADCON)
Table 13
ADC Control register (address C5H)
Table 14
Description of the ADCON bits
Table 15
ADCI and ADCS operating modes
If ADCI is cleared by software while ADCS is set at the same time a new analog-to-digital conversion with the same
channel-number may be started. It is recommended to reset ADCI before ADCS is set.
Note
1.
Start of a new conversion requires ADCI = 0.
7
6
5
4
3
2
1
0
ADC.1
ADC.0
ADEX
ADCI
ADCS
AADR2
AADR1
AADR0
BIT SYMBOL
FUNCTION
7
6
5
ADC.1
ADC.0
ADEX
Bit 1 of ADC converted value.
Bit 0 of ADC converted value.
Enable external start of conversion by STADC. If ADEX is:
LOW, then conversion cannot be started externally by STADC (only by software by setting ADCS)
HIGH, then conversion can be started externally by a rising edge on STADC or externally.
ADC interrupt flag.
This flag is set when an analog-to-digital conversion result is ready to be read.
If enabled, an interrupt is invoked. The flag must be cleared by software.
It cannot be set by software (see Table 15).
ADC start and status.
Setting this bit starts an analog-to-digital conversion. It may be set by
software or by the external signal STADC. The ADC logic ensures that this signal is HIGH while the
ADC is busy. On completion of the conversion, ADCS is reset at the same time the interrupt flag
ADCI is set. ADCS can not be reset by software (see Table 15).
Analog input select
. This binary coded address selects one of the eight analog port pins of P5 to be
input to the converter. It can only be changed when ADCI and ADCS are both LOW. AADR2 is the
MSB. (e.g. 100B selects the analog input channel ADC4)
4
ADCI
3
ADCS
2
1
0
AADR2
AADR1
AADR0
ADCI
ADCS
OPERATION
0
0
1
0
1
ADC not busy, a conversion can be started.
ADC busy, start of a new conversion is blocked.
Conversion completed; see note 1.
X (don’t care)
相關PDF資料 |
PDF描述 |
|---|---|
| P80C592FHA | 8-bit microcontroller with on-chip CAN |
| P83C592FHA | 8-bit microcontroller with on-chip CAN |
| P80C592 | 8-bit microcontroller with on-chip CAN |
| P83C592 | 8-bit microcontroller with on-chip CAN |
| P87C592EFA | 8-bit microcontroller with on-chip CAN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P83C592FHA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN |
| P83C652EBA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| P83C652EBAA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| P83C652EBB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| P83C652EBBB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。