參數資料
型號： P89LPC9321FDH,512
廠商： NXP Semiconductors
文件頁數： 18/71頁
文件大?。?/td> 0K
描述： IC 80C51 MCU 8KB FLASH 28TSSOP
標準包裝： 51
系列： LPC900
核心處理器： 8051
芯體尺寸： 8-位
速度： 18MHz
連通性： I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 26
程序存儲器容量： 8KB（8K x 8）
程序存儲器類型： 閃存
EEPROM 大小： 512 x 8
RAM 容量： 768 x 8
電壓 - 電源 (Vcc/Vdd)： 2.4 V ~ 3.6 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 28-TSSOP（0.173"，4.40mm 寬）
包裝： 管件
P89LPC9321
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 16 November 2010
25 of 71
NXP Semiconductors
P89LPC9321
8-bit microcontroller with accelerated two-clock 80C51 core
Each interrupt source can be individually programmed to one of four priority levels by
setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1 and IP1H. An
interrupt service routine in progress can be interrupted by a higher priority interrupt, but
not by another interrupt of the same or lower priority. The highest priority interrupt service
cannot be interrupted by any other interrupt source. If two requests of different priority
levels are pending at the start of an instruction, the request of higher priority level is
serviced.
If requests of the same priority level are pending at the start of an instruction, an internal
polling sequence determines which request is serviced. This is called the arbitration
ranking. Note that the arbitration ranking is only used to resolve pending requests of the
same priority level.
7.15.1 External interrupt inputs
The P89LPC9321 has two external interrupt inputs as well as the Keypad Interrupt
function. The two interrupt inputs are identical to those present on the standard 80C51
microcontrollers.
These external interrupts can be programmed to be level-triggered or edge-triggered by
setting or clearing bit IT1 or IT0 in Register TCON.
In edge-triggered mode, if successive samples of the INTn pin show a HIGH in one cycle
and a LOW in the next cycle, the interrupt request flag IEn in TCON is set, causing an
interrupt request.
If an external interrupt is enabled when the P89LPC9321 is put into Power-down or Idle
mode, the interrupt will cause the processor to wake-up and resume operation. Refer to
相關PDF資料
PDF描述
P89LPC9321FDH,518 IC 80C51 MCU FLASH 8K 28-TSSOP
VI-BN3-IX-F4 CONVERTER MOD DC/DC 24V 75W
VI-BN3-IX-F3 CONVERTER MOD DC/DC 24V 75W
VI-BN3-IX-F1 CONVERTER MOD DC/DC 24V 75W
VI-BN3-IW-F4 CONVERTER MOD DC/DC 24V 100W
相關代理商/技術參數
參數描述
P89LPC9321FN 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM
P89LPC9321FN,112 功能描述:8位微控制器 -MCU Enhanced LPC932A1 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC932A1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-Bit Microcontroller with accelerated two-clock 80C51 core 8kB 3V byte-erasable flash with 512-byte data EEPROM
P89LPC932A1FA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-Bit Microcontroller with accelerated two-clock 80C51 core 8kB 3V byte-erasable flash with 512-byte data EEPROM
P89LPC932A1FA,112 功能描述:8位微控制器 -MCU 8K FL/768B RAM/512B EE/CCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*