參數資料
型號： PCA9504A
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： Glue chip 4
中文描述： SPECIALTY MICROPROCESSOR CIRCUIT, PDSO56
封裝： 6.10 MM, PLASTIC, MO-153, SOT-364-1, TSSOP-56
文件頁數： 22/29頁
文件大?。?/td> 146K
代理商： PCA9504A
Philips Semiconductors
Product data
PCA9504A
Glue chip 4
2004 May 11
22
SW00593
LATCHED_BACKFEED_CUT
BACKFEED_CUT*
SLP_S5*
T1
T2
Figure 14. Power up signal sequencing
Power up signal sequencing is shown in Figure 14. BACKFEED_CUT* is following the power rail up to its final value.
LATCHED_BACKFEED_CUT should stay LOW, never turning on. SLP_S5* goes to its HIGH value when the power rails have stabilized,
25 msec after power on. BACKFEED_CUT* is pulled LOW a period T1 after SLP_S5* goes HIGH. T1 can be as short as 1msec. Typical
measured values are
200 msec. T1 and T2 are guaranteed by the inherent design of the system and are not controlled by Glue Chip.
SW00594
LATCHED_BACKFEED_CUT
BACKFEED_CUT*
Tpropr
Tr
Tpropf
Tf
SLP_S5*
Figure 15. 1st sequence timing
The first possible sequence is with SLP_S5*staying HIGH and BACKFEED_CUT* transitioning from LOW to HIGH, remaining HIGH for an
undetermined period and then going back to LOW and the system is back at the end of the power-up sequence. The power-up sequence is
shown in Figure 15. During these BACKFEED_CUT* transitions, the propagation delays, rise and fall times, and going into regulation times
LATCHED_BACKFEED_CUT are as described in Figure 16. The first sequence starts can start at the end of the power-up sequence at any time.
SW00595
LATCHED_BACKFEED_CUT
BACKFEED_CUT*
T3
Tpropf
SLP_S5*
Tpropr
Tr
Tf
T4
Figure 16. 2nd sequence timing
Signal sequencing for the second possible sequence is shown in Figure 16. BACKFEED_CUT* goes from LOW to HIGH and SLP_S5* goes
from HIGH to LOW, 30
μ
sec to 65
μ
sec (T3) later. LATCHED_BACKFEED_CUT goes HIGH when BACKFEED_CUT* goes HIGH and then
LATCHED_BACKFEED_CUT returns to LOW when SLP_S5* goes LOW. BACKFEED_CUT* stays HIGH and SLP_S5* stays LOW for an
indeterminate time and then SLP_S5* will go HIGH. A minimum of 1msec (T4) later, BACKFEED_CUT* will go LOW and the system is back at
the end of the power-up sequence. Typical measured values of T4 are
times, and going into regulation times for LATCHED_BACKFEED_CUT are as described in Figure 16. The first sequence starts can start at the
end of the power-up sequence at any time.
250 msec. During all transitions, the propagation delays, rise and fall
相關PDF資料
PDF描述
PCA9537 4-bit I2C and SMBus low power I/O port with interrupt and reset
PCA9553D01 4-bit I2C LED driver with programmable blink rates
PCA9553 RD-9ASJS ; 9 PIN FEMALE RoHS Compliant: Yes
PCA9553D02 4-bit I2C LED driver with programmable blink rates
PCA9553DP01 4-bit I2C LED driver with programmable blink rates
相關代理商/技術參數
參數描述
PCA9504ADGG 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Glue chip 4
PCA9504ADGG,112 功能描述:接口 - 專用 GLUE CHIP 4 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
PCA9504ADGG,118 功能描述:接口 - 專用 GLUE CHIP 4 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
PCA9504AT 制造商:NXP Semiconductors 功能描述:
PCA9505 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:40-bit I2C-bus I/O port with RESET, OE and INT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*