- 您現在的位置：買賣IC網 > PDF目錄17760 > PCA9534PW/DG,118 (NXP Semiconductors)IC I/O EXPANDER I2C/SMBU 16TSSOP PDF資料下載
參數資料
| 型號： | PCA9534PW/DG,118 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 22/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C/SMBU 16TSSOP |
| 標準包裝： | 2,500 |
| 系列： | * |
PCA9534_3
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 03 — 6 November 2006
6 of 25
NXP Semiconductors
PCA9534
8-bit I2C-bus and SMBus low power I/O port with interrupt
6.1.5 Register 3 - Conguration register
This register congures the directions of the I/O pins. If a bit in this register is set, the
corresponding port pin is enabled as an input with high-impedance output driver. If a bit in
this register is cleared, the corresponding port pin is enabled as an output. At reset, the
I/Os are congured as inputs.
6.2 Power-on reset
When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9534 in
a reset condition until VDD has reached VPOR. At that point, the reset condition is released
and the PCA9534 registers and state machine will initialize to their default states.
Thereafter, VDD must be lowered below 0.2 V to reset the device.
For a power reset cycle, VDD must be lowered below 0.2 V and then restored to the
operating voltage.
6.3 Interrupt output
The open-drain interrupt output is activated when one of the port pins change state and
the pin is congured as an input. The interrupt is deactivated when the input returns to its
previous state or the Input Port register is read.
Note that changing an I/O from and output to an input may cause a false interrupt to occur
if the state of the pin does not match the contents of the Input Port register.
6.4 I/O port
When an I/O is congured as an input, FETs Q1 and Q2 are off, creating a
high-impedance input. The input voltage may be raised above VDD to a maximum of 5.5 V.
If the I/O is congured as an output, then either Q1 or Q2 is enabled, depending on the
state of the Output Port register. Care should be exercised if an external voltage is applied
to an I/O congured as an output because of the low-impedance paths that exist between
the pin and either VDD or VSS.
Table 7.
Register 3 - Conguration register bit description
Legend: * default value.
Bit
Symbol
Access
Value
Description
7
C7
R/W
1*
congures the directions of the I/O pins
0 = corresponding port pin enabled as an output
1 = corresponding port pin congured as input
(default value)
6
C6
R/W
1*
5
C5
R/W
1*
4
C4
R/W
1*
3
C3
R/W
1*
2
C2
R/W
1*
1
C1
R/W
1*
0
C0
R/W
1*
相關PDF資料 |
PDF描述 |
|---|---|
| BDNF600A | SWITCH DISCONNECT 800A 1000V |
| CPPC8-LT5RP | OSC 3.3V PROG CMOS PWRDN 25PPM |
| CPPC8-LT5RT | OSC 3.3V PROG CMOS TRI ST 25PPM |
| CPPC8-LT0RT | OSC 3.3V PROG CMOS TRI ST 25PPM |
| CPPC8-LT0RP | OSC 3.3V PROG CMOS PWRDN 25PPM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9534PWG4 | 功能描述:接口-I/O擴展器 Rem 8B I2C & Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9534PWR | 功能描述:接口-I/O擴展器 Remote 8B I2C & Lo- Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9534PWRG4 | 功能描述:接口-I/O擴展器 Remote 8B I2C & Lo- Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9534RGTR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS |
| PCA9534RGVR | 功能描述:接口-I/O擴展器 Remote 8B I2C & Lo- Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。