- 您現在的位置：買賣IC網 > PDF目錄224694 > PCA9551D (NXP Semiconductors N.V.) 8-bit I2C-bus LED driver with programmable blink rates PDF資料下載
參數資料
| 型號： | PCA9551D |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | LED驅動器 |
| 英文描述： | 8-bit I2C-bus LED driver with programmable blink rates |
| 封裝： | PCA9551BS<SOT629-1 (HVQFN16)|<<http://www.nxp.com/packages/SOT629-1.html<1<Always Pb-free,;PCA9551D<SOT109-1 (SO16)|<<http://www.nxp.com/packages/SOT109-1.html<1<we |
| 文件頁數： | 24/26頁 |
| 文件大?。?/td> | 155K |
| 代理商： | PCA9551D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁
PCA9551_8
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 08 — 31 July 2008
7 of 26
NXP Semiconductors
PCA9551
8-bit I2C-bus LED driver with programmable blink rates
6.3.6 LS0 to LS1 - LED selector registers
The LSn LED select registers determine the source of the LED data.
00 = output is set LOW (LED on)
01 = output is set high-impedance (LED off; default)
10 = output blinks at PWM0 rate
11 = output blinks at PWM1 rate
6.4 Pins used as GPIOs
LED pins not used to control LEDs can be used as general purpose I/Os (GPIOs).
For use as input, set LEDn to high-impedance (01) and then read the pin state via the
Input register.
For use as output, connect external pull-up resistor to the pin and size it according to the
DC recommended operating characteristics. LEDn output pin is HIGH when the output is
programmed as high-impedance, and LOW when the output is programmed LOW through
the ‘LED selector’ register. The output can be pulse-width controlled when PWM0 or
PWM1 are used.
6.5 Power-on reset
When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9551 in
a reset condition until VDD has reached VPOR. At that point, the reset condition is released
and the PCA9551 registers are initialized to their default states, all the outputs in the
OFF state. Thereafter, VDD must be lowered below 0.2 V to reset the device.
6.6 External RESET
A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst). The
PCA9551 registers and I2C-bus state machine will be held in their default states until the
RESET input is once again HIGH.
This input requires a pull-up resistor to VDD if no active connection is used.
Table 9.
LS0 to LS1 - LED selector registers bit description
Legend: * default value.
Register
Bit
Value
Description
LS0 - LED0 to LED3 selector
LS0
7:6
01*
LED3 selected
5:4
01*
LED2 selected
3:2
01*
LED1 selected
1:0
01*
LED0 selected
LS1 - LED4 to LED7 selector
LS1
7:6
01*
LED7 selected
5:4
01*
LED6 selected
3:2
01*
LED5 selected
1:0
01*
LED4 selected
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9551PW | 8-bit I2C-bus LED driver with programmable blink rates |
| PCA9552BS | 16-bit I2C-bus LED driver with programmable blink rates |
| PCA9552D | 16-bit I2C-bus LED driver with programmable blink rates |
| PCA9552PW | 16-bit I2C-bus LED driver with programmable blink rates |
| PCA9553D | 4-bit I2C-bus LED driver with programmable blink rates |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9551D,112 | 功能描述:LED照明驅動器 I2C LED BLINKER 8BIT RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| PCA9551D,118 | 功能描述:LED照明驅動器 8-BIT I2C FM OD LED BLK RST RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| PCA9551D-T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit I2C-bus LED driver with programmable blink rates |
| PCA9551PW | 功能描述:LED照明驅動器 I2C LED BLINKER 8BIT RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| PCA9551PW,112 | 功能描述:LED照明驅動器 I2C LED BLINKER 8BIT RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。