- 您現在的位置：買賣IC網 > PDF目錄224694 > PCA9553D (NXP Semiconductors N.V.) 4-bit I2C-bus LED driver with programmable blink rates PDF資料下載
參數資料
| 型號： | PCA9553D |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | LED驅動器 |
| 英文描述： | 4-bit I2C-bus LED driver with programmable blink rates |
| 封裝： | PCA9553D/01<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 5, 2005,;PCA9553D/01<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 5, |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 146K |
| 代理商： | PCA9553D |
PCA9553_6
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 06 — 29 December 2008
8 of 26
NXP Semiconductors
PCA9553
4-bit I2C-bus LED driver with programmable blink rates
7.4 Pins used as general purpose I/Os
LED pins not used to control LEDs can be used as general purpose I/Os.
For use as input: Set LEDn to high-impedance (01) and then read the pin state via the
Input register.
For use as output: Connect external pull-up resistor to the pin and size it according to the
DC recommended operating characteristics. LED output pin is HIGH when the output is
programmed as high-impedance, and LOW when the output is programmed LOW through
the ‘LED selector’ register. The output can be pulse-width controlled when PWM0 or
PWM1 are used.
7.5 Power-on reset
When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9553 in
a reset condition until VDD has reached VPOR. At that point, the reset condition is released
and the PCA9553 registers are initialized to their default states, with all outputs in the OFF
state. Thereafter, VDD must be lowered below 0.2 V to reset the device.
8.
Characteristics of the I2C-bus
The I2C-bus is for 2-way, 2-line communication between different ICs or modules. The two
lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be
connected to a positive supply via a pull-up resistor when connected to the output stages
of a device. Data transfer may be initiated only when the bus is not busy.
8.1 Bit transfer
One data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the HIGH period of the clock pulse as changes in the data line at this time
will be interpreted as control signals (see Figure 8).
8.1.1 START and STOP conditions
Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW
transition of the data line while the clock is HIGH is dened as the START condition (S). A
LOW-to-HIGH transition of the data line while the clock is HIGH is dened as the STOP
condition (P) (see Figure 9).
Fig 8.
Bit transfer
mba607
data line
stable;
data valid
change
of data
allowed
SDA
SCL
相關PDF資料 |
PDF描述 |
|---|---|
| PCB25 | POWER CONNECTOR |
| PCF8578T | LCD row-column driver for dot matrix graphic displays |
| PCI-36RS-SB-L | STRAIGHT TELECOM AND DATACOM CONNECTOR |
| PCI-36SS-SB-N | STRAIGHT TELECOM AND DATACOM CONNECTOR |
| PCI-36SS-B-H | STRAIGHT TELECOM AND DATACOM CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9553D/01 | 功能描述:LED照明驅動器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| PCA9553D/01,112 | 功能描述:LED照明驅動器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| PCA9553D/01,118 | 功能描述:LED照明驅動器 4-BIT I2C FM OD LED BLK RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| PCA9553D/01112 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| PCA9553D/02 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4-bit I2C-bus LED driver with programmable blink rates |
發布緊急采購，3分鐘左右您將得到回復。