參數資料
型號： PCIB40
英文描述： PC(ISA)BUS I/O CARD
中文描述： 電腦（ISA）總線的I / O卡
文件頁數： 8/16頁
文件大小： 284K
代理商： PCIB40
2192-09066-000-000
J206 PCIB40 Technical Manual
8
Link 1
Counter 0 Clock Frequency Select
The clock input for counter 0 can be connected to an on-board clock generator operating at either
10KHz, 100KHz or 1MHz. This is set using LK1A/B/C.
Links 10-14
Power-Up Output State
These links are used to select the power-up state of the five groups of I/O channels. For more
information see page 4.
Links 20-24
Power-up control
Select whether the output buffer is always enabled or controlled by software. If you are configuring
the board for known boot up state then the group must be software enabled. If link B is fitted the
output state cannot be determined (‘don’t care’ state) at power up or reset.
Link IRQ2-5 & 7
Interrupt select
The output of counter 0 can be used to generate an interrupt on either IRQ 2,3,4,5 or 7.
NOTE:
A PC must be configured with only one interrupt source for each interrupt line. Check your
PC configuration before selecting the interrupt signal. If you are not using the interrupt facility, it is
recommended that the jumper is not fitted.
LK20
Position A Group 0 Outputs enabled by ‘software’
Position B Group 0 Outputs always enabled after power on/reset
Position A Group 1 Outputs enabled by ‘software’
Position B Group 1 Outputs always enabled after power on/reset
Position A Group 2 Outputs enabled by ‘software’
Position B Group 2 Outputs always enabled after power on/reset
Position A Group 3 Outputs enabled by ‘software’
Position B Group 3 Outputs always enabled after power on/reset
Position A Group 4 Outputs enabled by ‘software’
Position B Group 4 Outputs always enabled after power on/reset
LK21
LK22
LK23
LK24
LK1A
Clock input = 1MHz
Clock input = 100KHz
Clock input = 10KHz
LK1B
LK1C
IRQ2
Timer interrupt on IRQ2
Timer interrupt on IRQ3
Timer interrupt on IRQ4
Timer interrupt on IRQ5
Timer interrupt on IRQ7
IRQ3
IRQ4
IRQ5
IRQ7
LK10
Position A for Group 0 outputs set to ‘1’
Position B for Group 0 outputs reset to ‘0’
Position A for Group 1 outputs set to ‘1’
Position B for Group 1 outputs reset to ‘0’
Position A for Group 2 outputs set to ‘1’
Position B for Group 2 outputs reset to ‘0’
Position A for Group 3 outputs set to ‘1’
Position B for Group 3 outputs reset to ‘0’
Position A for Group outputs 4 set to ‘1’
Position B for Group outputs 4 reset to ‘0’
LK11
LK12
LK13
LK14
+
+
+
+
+
+
+
+
+
+
+
相關PDF資料
PDF描述
PCICLOCKGEN_R001 AMD Alchemy? Solutions Au1500? PCI Clock Generation?
PCK2000 CK97 (66/100MHz) System Clock Generator(CK97 (66/100MHz) 系統時鐘發生器)
PCK2000DL CK97 66/100MHz System Clock Generator
PCK2001M 14.318-150 MHz IIC 1:10 clock buffer(14.318-150 MHz IIC 1:10時鐘緩沖器)
PCK2001R 14.318-133 MHz I2C 1:6 Clock Buffer(14.318-133 MHz I2C 1:6時鐘緩沖器)
相關代理商/技術參數
參數描述
PCIC16W7M400C1 制造商:Positronic Industries 功能描述:
PCI-C588 功能描述:界面模塊 8 PORT ASYNC SERIAL COMM PCI CARD RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
PCI-C6600S4-2-67-167 制造商:Johnson Components 功能描述:SBC;DSP, 2 C9701, 2MB SRAM, IN
PCI-COM2 制造商:BCM Advanced Research 功能描述:2 PORT COM CARD - Bulk
PCI-COM4 制造商:BCM Advanced Research 功能描述:4 COM PORTS SERIAL CARD SUPPORTS 4 RX232/422/485 - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*