參數資料
型號： PDIUSBD12D
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： nullUSB interface device with parallel bus
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, PDSO28
封裝： 7.50 MM , PLASTIC, MS-013, SOT-136-1, SOP-28
文件頁數： 19/35頁
文件大?。?/td> 838K
代理商： PDIUSBD12D
Philips Semiconductors
PDIUSBD12
USB interface device with parallel bus
Product data
Rev. 08 — 20 December 2001
19 of 35
9397 750 09238
Koninklijke Philips Electronics N.V. 2001. All rights reserved.
11.3.5
Read buffer
Code (Hex) —
F0
Transaction —
read multiple bytes (max. 130)
The Read Buffer command is followed by a number of data reads, which returns the
contents of the selected endpoint data buffer. After each read, the internal buffer
pointer is incremented by 1.
The buffer pointer is not reset to the top of the buffer by the Read Buffer command.
This means that reading or writing a buffer can be interrupted by any other command
(except for Select Endpoint).
The data in the buffer are organized as follows:
byte 0: reserved; can have any value
byte 1: number/length of data bytes
byte 2: data byte 1
byte 3: data byte 2
etc.
The first two bytes will be skipped in the DMA read operation. Thus, the first read will
get Data byte 1, the second read will get Data byte 2, etc. The PDIUSBD12 can
determine the last byte of this packet through the EOP termination of the USB packet.
11.3.6
Write buffer
Code (Hex) —
F0
Transaction —
write multiple bytes (max. 130)
The Write Buffer command is followed by a number of data writes, which load the
endpoints buffer. The data must be organized in the same way as described in the
Read Buffer command. The first byte (reserved) should always be ‘0’.
During DMA write operation, the first two bytes will be bypassed. Thus, the first write
will write into Data byte 1, the second write will write into Data byte 2, etc. For
non-isochronous transfer (bulk or interrupt), the buffer should be completely filled
before the data is sent to the host and a switch to the next buffer occurs. The
exception is at the end of DMA transfer indicated by activation of EOT_N, when the
current buffer content (completely full or not) will be sent to the host.
Remark:
There is no protection against writing or reading over a buffer’s boundary or
against writing into an OUT buffer or reading from an IN buffer. Any of these actions
could cause an incorrect operation. Data in an OUT buffer are only meaningful after a
1011
Overflow Error, the received packet was longer than the available buffer
space
Bitstuff Error
Wrong DATA PID; the received DATA PID was not the expected one
1101
1111
Table 10:
Error
code (Binary)
Error codes
…continued
Description
相關PDF資料
PDF描述
PDIUSBD12PW nullUSB interface device with parallel bus
PDIUSBH11A Universal Serial Bus hub(通用串行總線集線器)
PDIUSBH11ANB Universal Serial Bus Hub
PDIUSBH11AD Universal Serial Bus Hub
PDIUSBH11 Universal Serial Bus Hub
相關代理商/技術參數
參數描述
PDIUSBD12D,112 功能描述:USB 接口集成電路 USB INTRFC W/PARL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
PDIUSBD12D,118 功能描述:USB 接口集成電路 USB I-FACE W/PARALLEL BUS RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
PDIUSBD12D.112 制造商:NXP Semiconductors 功能描述:USB INTERFACE DEVICE SMD SOIC28
PDIUSBD12DAA 功能描述:IC USB INTRFC W/PARL BUS 28-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
PDIUSBD12D-T 制造商:ST-Ericsson 功能描述:USB Peripheral Controller 28-Pin SO T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*