參數資料
型號： PDIUSBH12
廠商： NXP Semiconductors N.V.
英文描述： USB 2-port hub
中文描述： 2的USB端口集線器
文件頁數： 9/28頁
文件大?。?/td> 170K
代理商： PDIUSBH12
Philips Semiconductors
Product specification
PDIUSBH12
USB 2-port hub
1999 Jul 22
9
APPLICATION DIAGRAM
I
2
C
GOODLINK
LED
POWER SWITCH
AND
OVERCURRENT CIRCUIT
5V
SWITCHED
5V
H12
μ
C
CLKOUT
12MHz
USB
DOWNSTREAM
USB
UPSTREAM
3.3V
SV00853
I
2
C Interface
The I
2
C bus is used to interface to an external microcontroller
needed to control the operation of the hub. For cost consideration,
the target system microcontroller can be shared and utilized for this
purpose. The PDIUSBH12 implements a slave I
2
C interface. When
the PDIUSBH12 needs to communicate with the microcontroller it
asserts an interrupt signal. The microcontroller services this interrupt
by reading the appropriate status register on the PDIUSBH12
through the I
2
C bus. (For more information about the I
2
C serial bus,
refer to the I
2
C Handbook Philips order number 9397 750 00013).
The I
2
C interface on the PDIUSBH12 defines two types of
transactions:
1.
command transaction
A command transaction is used to define which data (e.g., status
byte, buffer data, ...) will be read from / written to the USB
interface in the next data transaction. A data transaction usually
follows a command transaction.
2.
data transaction
A data transaction reads data from / writes data to the USB
interface. The meaning of the data is dependent on the
command transaction which was sent before the data
transaction.
Two addresses are used to differentiate between command and
data transactions. Writing to the command address is interpreted as
a command, while reading from / writing to the data address is used
to transfer data between the PDIUSBH12 and the controller.
ADDRESS TABLE
TYPE OF ADDRESS
PHYSICAL ADDRESS
(MSB to LSB)
Command
0011 011 (binary)
Data
0011 010 (binary)
Protocol
An I
2
C transaction starts with a ‘Start Condition’, followed by an
address. When the address matches either the command or data
address the transaction starts and runs until a ‘Stop Condition’ or
another ‘Start Condition’ (repeated start) occurs.
The command address is write-only and is unable to do a read. The
next bytes in the message are interpreted as commands. Several
command bytes can be sent after one command address. Each of
the command bytes is acknowledged and passed on to the Memory
Management Unit inside the PDIUSBH12.
When the start condition address matches the data address, the
next bytes are interpreted as data. When the RW bit in the address
indicates a ‘master writes data to slave’ (=‘0’) the bytes are received,
acknowledged and passed on to the Memory Management Unit. If
the RW bit in the address indicates a ‘master reads data from slave’
(=‘1’) the PDIUSBH12 will send data to the master. The I
2
C-master
must acknowledge all data bytes except the last one. In this way the
I
2
C interface knows when the last byte has been transmitted and it
then releases the SDA line so that the master controller can
generate the STOP condition.
Repeated start support allows another packet to be sent without
generating a Stop Condition.
Timing
The I
2
C interface in the PDIUSBH12 can support clock speeds up to
1MHz.
相關PDF資料
PDF描述
PDIUSBH12D USB 2-port hub
PDIUSBH12N USB 2-port hub
PDIUSBP11A Universal Serial Bus Transceiver(通用串行總線收發器)
PDUSBP11APWDH Universal Serial Bus Transceiver
PDIUSBP11AD Universal Serial Bus Transceiver
相關代理商/技術參數
參數描述
PDIUSBH12D 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB 2-port hub
PDIUSBH12N 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB 2-port hub
PDIUSBH12NB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER
PDIUSBP11 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus transceiver
PDIUSBP11A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*