參數資料
型號: PIC10F202T
廠商: Microchip Technology Inc.
英文描述: 6-Pin, 8-Bit Flash Microcontrollers
中文描述: 6引腳,8位閃存微控制器
文件頁數: 37/86頁
文件大?。?/td> 620K
代理商: PIC10F202T
2005 Microchip Technology Inc.
Preliminary
DS41239B-page 35
PIC10F200/202/204/206
7.1.2
TIMER0 INCREMENT DELAY
Since the prescaler output is synchronized with the
internal clocks, there is a small delay from the time the
external clock edge occurs to the time the Timer0
module is actually incremented. Figure 7-4 shows the
delay from the external clock edge to the timer
incrementing.
FIGURE 7-4:
TIMER0 TIMING WITH EXTERNAL CLOCK
7.2
Prescaler
An 8-bit counter is available as a prescaler for the
Timer0 module or as a postscaler for the Watchdog
Timer (WDT), respectively (see Figure 9-6). For
simplicity, this counter is being referred to as
“prescaler” throughout this data sheet.
The PSA and PS<2:0> bits (OPTION<3:0>) determine
prescaler assignment and prescale ratio.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g.,
CLRF 1
,
MOVWF 1
,
BSF 1,x
, etc.) will clear the prescaler. When assigned
to WDT, a
CLRWDT
instruction will clear the prescaler
along with the WDT. The prescaler is neither readable
nor writable. On a Reset, the prescaler contains all ‘
0
’s.
7.2.1
SWITCHING PRESCALER
ASSIGNMENT
The prescaler assignment is fully under software
control (i.e., it can be changed “on-the-fly” during pro-
gram execution). To avoid an unintended device Reset,
the following instruction sequence (Example 7-1) must
be executed when changing the prescaler assignment
from Timer0 to the WDT.
EXAMPLE 7-1:
CHANGING PRESCALER
(TIMER0
WDT)
;Clear WDT
;Clear TMR0 & Prescaler
‘00xx1111’b ;These 3 lines (5, 6, 7)
;are required only if
;desired
;PS<2:0> are 000 or 001
‘00xx1xxx’b ;Set Postscaler to
;desired WDT rate
Increment Timer0 (Q4)
External Clock Input or
Prescaler Output
(2)
Q1 Q2
Q3
Q4
Q1 Q2
Q3
Q4
Q1 Q2 Q3
Q4
Q1 Q2
Q3
Q4
Timer0
T0
T0 + 1
T0 + 2
Small pulse
misses sampling
External Clock/Prescaler
Output After Sampling
(3)
(1)
Note 1:
Delay from clock input change to Timer0 increment is 3 T
OSC
to 7 T
OSC
(Duration of Q = T
OSC
). Therefore, the error
in measuring the interval between two edges on Timer0 input = ±4 T
OSC
max.
External clock if no prescaler selected; prescaler output otherwise.
The arrows indicate the points in time where sampling occurs.
2:
3:
Note:
The prescaler may be used by either the
Timer0 module or the WDT, but not both.
Thus, a prescaler assignment for the
Timer0 module means that there is no
prescaler for the WDT and vice versa.
CLRWDT
CLRF
MOVLW
OPTION
TMR0
CLRWDT
MOVLW
OPTION
相關PDF資料
PDF描述
PIC10F200 6-Pin, 8-Bit Flash Microcontrollers
PIC10F200T 6-Pin, 8-Bit Flash Microcontrollers
PIC10F202 6-Pin, 8-Bit Flash Microcontrollers
PIC10F204 6-Pin, 8-Bit Flash Microcontrollers
PIC10F204T 6-Pin, 8-Bit Flash Microcontrollers
相關代理商/技術參數
參數描述
PIC10F202T-E/MC 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:6-Pin, 8-Bit Flash Microcontrollers
PIC10F202T-E/OT 功能描述:8位微控制器 -MCU .75kBF 24RM 4I/O Ext Temp SOT-23 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC10F202T-E/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:6-Pin, 8-Bit Flash Microcontrollers
PIC10F202T-I/MC 功能描述:8位微控制器 -MCU 0.75KB Fl 24B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC10F202T-I/OT 功能描述:8位微控制器 -MCU .75kBF 24RM 4I/O Ind Temp SOT-23 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT