參數資料
型號： PIC10F202T
廠商： Microchip Technology Inc.
英文描述： 6-Pin, 8-Bit Flash Microcontrollers
中文描述： 6引腳，8位閃存微控制器
文件頁數： 52/86頁
文件大?。?/td> 620K
代理商： PIC10F202T
PIC10F200/202/204/206
DS41239B-page 50
Preliminary
2005 Microchip Technology Inc.
9.10
Program Verification/Code
Protection
If the code protection bit has not been programmed, the
on-chip program memory can be read out for
verification purposes.
The first 64 locations and the last location (Reset
vector) can be read, regardless of the code protection
bit setting.
9.11
ID Locations
Four memory locations are designated as ID locations
where the user can store checksum or other code
identification numbers. These locations are not
accessible during normal execution, but are readable
and writable during Program/Verify.
Use only the lower 4 bits of the ID locations and always
program the upper 8 bits as ‘
0
’s.
9.12
In-Circuit Serial Programming
The PIC10F200/202/204/206 microcontrollers can be
serially programmed while in the end application circuit.
This is simply done with two lines for clock and data,
and three other lines for power, ground and the
programming voltage. This allows customers to manu-
facture boards with unprogrammed devices and then
program the microcontroller just before shipping the
product. This also allows the most recent firmware or a
custom firmware, to be programmed.
The devices are placed into a Program/Verify mode by
holding the GP1 and GP0 pins low while raising the
MCLR (V
PP
) pin from V
IL
to V
IHH
(see programming
specification). GP1 becomes the programming clock
and GP0 becomes the programming data. Both GP1
and GP0 are Schmitt Trigger inputs in this mode.
After Reset, a 6-bit command is then supplied to the
device. Depending on the command, 16 bits of program
data are then supplied to or from the device, depending
if the command was a Load or a Read. For complete
details of serial programming, please refer to the
PIC10F200/202/204/206 Programming Specifications.
A typical In-Circuit Serial Programming connection is
shown in Figure 9-10.
FIGURE 9-10:
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
External
Connector
Signals
To Normal
Connections
To Normal
Connections
PIC10F20X
V
DD
V
SS
MCLR/V
PP
GP1
GP0
+5V
0V
V
PP
CLK
Data I/O
V
DD
相關PDF資料
PDF描述
PIC10F200 6-Pin, 8-Bit Flash Microcontrollers
PIC10F200T 6-Pin, 8-Bit Flash Microcontrollers
PIC10F202 6-Pin, 8-Bit Flash Microcontrollers
PIC10F204 6-Pin, 8-Bit Flash Microcontrollers
PIC10F204T 6-Pin, 8-Bit Flash Microcontrollers
相關代理商/技術參數
參數描述
PIC10F202T-E/MC 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:6-Pin, 8-Bit Flash Microcontrollers
PIC10F202T-E/OT 功能描述:8位微控制器 -MCU .75kBF 24RM 4I/O Ext Temp SOT-23 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC10F202T-E/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:6-Pin, 8-Bit Flash Microcontrollers
PIC10F202T-I/MC 功能描述:8位微控制器 -MCU 0.75KB Fl 24B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC10F202T-I/OT 功能描述:8位微控制器 -MCU .75kBF 24RM 4I/O Ind Temp SOT-23 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*