參數資料
型號: PIC12F1501-I/MF
廠商: Microchip Technology
文件頁數: 20/33頁
文件大?。?/td> 0K
描述: IC MCU 8BIT 1.75KB FLASH 8-DFN
標準包裝: 120
系列: PIC® 12F
核心處理器: PIC
芯體尺寸: 8-位
速度: 20MHz
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 5
程序存儲器容量: 1.75KB(1K x 14)
程序存儲器類型: 閃存
RAM 容量: 64 x 8
電壓 - 電源 (Vcc/Vdd): 2.3 V ~ 5.5 V
數據轉換器: A/D 4x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 8-VDFN 裸露焊盤
包裝: 管件
PIC18F1220/1320
DS39605F-page 26
2007 Microchip Technology Inc.
3.4
Run Modes
If the IDLEN bit is clear when a SLEEP instruction is
executed, the CPU and peripherals are both clocked
from the source selected using the SCS1:SCS0 bits.
While these operating modes may not afford the power
conservation of Idle or Sleep modes, they do allow the
device to continue executing instructions by using a
lower frequency clock source. RC_RUN mode also
offers the possibility of executing code at a frequency
greater than the primary clock.
Wake-up from a power managed Run mode can be
triggered by an interrupt, or any Reset, to return to full
power operation. As the CPU is executing code in Run
modes, several additional exits from Run modes are
possible. They include exit to Sleep mode, exit to a cor-
responding Idle mode and exit by executing a RESET
instruction. While the device is in any of the power
managed Run modes, a WDT time-out will result in a
WDT Reset.
3.4.1
PRI_RUN MODE
The PRI_RUN mode is the normal full power execution
mode. If the SLEEP instruction is never executed, the
microcontroller operates in this mode (a SLEEP instruc-
tion is executed to enter all other power managed
modes). All other power managed modes exit to
PRI_RUN mode when an interrupt or WDT time-out
occur.
There is no entry to PRI_RUN mode. The OSTS bit is
set. The IOFS bit may be set if the internal oscillator
block is the primary clock source (see Section 2.7.1
3.4.2
SEC_RUN MODE
The SEC_RUN mode is the compatible mode to the
“clock switching” feature offered in other PIC18
devices. In this mode, the CPU and peripherals are
clocked from the Timer1 oscillator. This gives users the
option of lower power consumption while still using a
high accuracy clock source.
SEC_RUN mode is entered by clearing the IDLEN bit,
setting SCS1:SCS0 = 01 and executing a SLEEP
instruction. The system clock source is switched to the
Timer1 oscillator (see Figure 3-9), the primary oscilla-
tor is shut down, the T1RUN bit (T1CON<6>) is set and
the OSTS bit is cleared.
When a wake event occurs, the peripherals and CPU
continue to be clocked from the Timer1 oscillator while
the primary clock is started. When the primary clock
becomes ready, a clock switchback to the primary clock
occurs (see Figure 3-6). When the clock switch is com-
plete, the T1RUN bit is cleared, the OSTS bit is set and
the primary clock is providing the system clock. The
IDLEN and SCS bits are not affected by the wake-up.
The Timer1 oscillator continues to run.
Firmware can force an exit from SEC_RUN mode. By
clearing the T1OSCEN bit (T1CON<3>), an exit from
SEC_RUN back to normal full power operation is trig-
gered. The Timer1 oscillator will continue to run and
provide the system clock, even though the T1OSCEN
bit is cleared. The primary clock is started. When the
primary clock becomes ready, a clock switchback to the
primary clock occurs (see Figure 3-6). When the clock
switch is complete, the Timer1 oscillator is disabled, the
T1RUN bit is cleared, the OSTS bit is set and the pri-
mary clock is providing the system clock. The IDLEN
and SCS bits are not affected by the wake-up.
FIGURE 3-9:
TIMING TRANSITION FOR ENTRY TO SEC_RUN MODE
Note:
The Timer1 oscillator should already be
running prior to entering SEC_RUN mode.
If the T1OSCEN bit is not set when the
SLEEP
instruction is executed, the SLEEP
instruction will be ignored and entry to
SEC_RUN mode will not occur. If the
Timer1 oscillator is enabled, but not yet
running, system clocks will be delayed
until the oscillator has started; in such
situations, initial oscillator operation is far
from stable and unpredictable operation
may result.
Q4
Q3
Q2
OSC1
Peripheral
Program
Q1
T1OSI
Q1
Counter
Clock
CPU
Clock
PC + 2
PC
123
4567
8
Clock Transition
Q4
Q3
Q2
Q1
Q3
Q2
PC + 2
相關PDF資料
PDF描述
PIC12F510-I/MC IC PIC MCU FLASH 1024X12 8DFN
PIC12F629T-I/MF IC MCU CMOS 8BIT 1K FLASH 8-DFN
PIC12LF1501-E/MS IC MCU 8BIT 1.75KB FLASH 8MSOP
PIC16F57-I/SS IC MCU FLASH 2KX12 28SSOP
PIC12F510-I/MS IC PIC MCU FLASH 1.5KB 8MSOP
相關代理商/技術參數
參數描述
PIC12F1501-I-MG 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:14-Pin Flash, 8-Bit Microcontrollers
PIC12F1501T-EMCQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash, 8-Bit Microcontrollers
PIC12F1501T-EMCSQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash, 8-Bit Microcontrollers
PIC12F1501T-EMFQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash, 8-Bit Microcontrollers
PIC12F1501T-EMFSQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash, 8-Bit Microcontrollers