參數資料
型號： PIC12F519-I/SN
廠商： Microchip Technology
文件頁數： 46/96頁
文件大小： 0K
描述： IC PIC MCU FLASH 1KX12 8SOIC
產品培訓模塊： Asynchronous Stimulus
8-bit PIC® Microcontroller Portfolio
標準包裝： 100
系列： PIC® 12F
核心處理器： PIC
芯體尺寸： 8-位
速度： 8MHz
外圍設備： POR，WDT
輸入/輸出數： 5
程序存儲器容量： 1.5KB（1K x 12）
程序存儲器類型： 閃存
RAM 容量： 41 x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 5.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
包裝： 管件
產品目錄頁面： 637 (CN2011-ZH PDF)
PIC12F519
DS41319B-page 48
2008 Microchip Technology Inc.
8.9
Program Verification/Code
Protection
If the code protection bits have not been programmed,
the on-chip program and data memory can be read out
for verification purposes.
The first 64 locations and the last location (OSCCAL)
can be read, regardless of the setting of the program
memory’s code protection bit. If the code protect bit
specific to the FLASH data memory is programmed,
then none of the contents of this memory region can be
verified externally.
8.10
ID Locations
Four memory locations are designated as ID locations
where users can store checksum or other code
identification numbers. These locations are not
accessible during normal execution, but are readable
and writable during program/verify.
Use only the lower 4 bits of the ID locations. The upper
bits should be programmed as 0s.
8.11
In-Circuit Serial Programming
The PIC12F519 device can be serially programmed
while in the end application circuit. This is simply done
with two lines for clock and data, and three other lines
for power, ground and the programming voltage. This
allows
users
to
manufacture
boards
with
unprogrammed PIC12F519 device and then program
the PIC12F519 device just before shipping the product.
This also allows the most recent firmware, or a custom
firmware, to be programmed.
The PIC12F519 device is placed into a Program/Verify
mode by holding the GP1 and GP0 pins low while
raising the MCLR (VPP) pin from VIL to VIHH (see
programming specification). The GP1 pin becomes the
programming clock, and the GP0 pin becomes the
programming data. Both GP1 and GP0 pins are Schmitt
Trigger inputs in this mode.
After Reset, a 6-bit command is then supplied to the
device. Depending on the command, 14 bits of program
data are then supplied to or from the device, depending
if the command was a Load or a Read. For complete
details of serial programming, please refer to the
“PIC12F519 Memory Programming Specification,”
(DS41316).
A typical In-Circuit Serial Programming connection is
shown in Figure 8-12.
FIGURE 8-12:
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
External
Connector
Signals
To Normal
Connections
To Normal
Connections
PIC12F519
VDD
VSS
MCLR/VPP
GP1/ICSPCLK
GP0/ICSPDAT
+5V
0V
VPP
CLK
Data
VDD
相關PDF資料
PDF描述
PIC12F510-I/SN IC PIC MCU FLASH 1.5KB 8SOIC
PIC12F509-I/MS IC PIC MCU FLASH 1KX12 8MSOP
PIC12F508-I/P IC MCU FLASH 512X12 8DIP
PIC16F505-I/SL IC MCU FLASH 1KX12 14SOIC
PIC12F629T-I/SN IC MCU CMOS 8BIT 1K FLASH 8-SOIC
相關代理商/技術參數
參數描述
PIC12F519T-E/MC 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit Flash Microcontroller
PIC12F519T-E/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit Flash Microcontroller
PIC12F519T-E/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit Flash Microcontroller
PIC12F519T-E/SN 制造商:Microchip Technology Inc 功能描述:8-PIN, 1.5KB FLASH PROGRAM, 64 - Tape and Reel
PIC12F519T-I/MC 功能描述:8位微控制器 -MCU 15KB Flash Prgrm 64B 8MHz Intrnl Oscilatr RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*