參數資料
型號： PIC16CR74-I/L
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQCC44
封裝： PLASTIC, LCC-44
文件頁數： 137/172頁
文件大?。?/td> 2964K
代理商： PIC16CR74-I/L
2007 Microchip Technology Inc.
DS21993C-page 65
PIC16CR7X
9.3
SSP I2C Operation
The SSP module in I2C mode fully implements all slave
functions except general call support, and provides
interrupts on Start and Stop bits in hardware to facilitate
firmware implementations of the master functions. The
SSP module implements the standard mode specifica-
tions as well as 7-bit and 10-bit addressing.
Two pins are used for data transfer. These are the RC3/
SCK/SCL pin, which is the clock (SCL), and the RC4/
SDI/SDA pin, which is the data (SDA). The user must
configure these pins as inputs or outputs through the
TRISC<4:3> bits.
The SSP module functions are enabled by setting SSP
enable bit SSPEN (SSPCON<5>).
FIGURE 9-5:
SSP BLOCK DIAGRAM
(I2C MODE)
The SSP module has five registers for I2C operation.
These are the:
SSP Control Register (SSPCON)
SSP Status Register (SSPSTAT)
Serial Receive/Transmit Buffer (SSPBUF)
SSP Shift Register (SSPSR) – Not directly
accessible
SSP Address Register (SSPADD)
The SSPCON register allows control of the I2C opera-
tion. Four mode selection bits (SSPCON<3:0>) allow
one of the following I2C modes to be selected:
I2C Slave mode (7-bit address)
I2C Slave mode (10-bit address)
I2C Slave mode (7-bit address), with Start and
Stop bit interrupts enabled to support Firmware
Master mode
I2C Slave mode (10-bit address), with Start and
Stop bit interrupts enabled to support Firmware
Master mode
I2C Start and Stop bit interrupts enabled to
support Firmware Master mode, Slave is Idle
Selection of any I2C mode with the SSPEN bit set,
forces the SCL and SDA pins to be open drain, pro-
vided these pins are programmed to inputs by setting
the appropriate TRISC bits. Pull-up resistors must be
provided externally to the SCL and SDA pins for proper
operation of the I2C module.
Additional information on SSP I2C operation can be
found in the “PIC Mid-Range MCU Family Reference
Manual” (DS33023).
9.3.1
SLAVE MODE
In Slave mode, the SCL and SDA pins must be config-
ured as inputs (TRISC<4:3> set). The SSP module will
override the input state with the output data when
required (slave-transmitter).
When an address is matched, or the data transfer after
an address match is received, the hardware automati-
cally will generate the Acknowledge (ACK) pulse, and
then load the SSPBUF register with the received value
currently in the SSPSR register.
There are certain conditions that will cause the SSP
module not to give this ACK pulse. They include (either
or both):
a)
The Buffer Full bit BF (SSPSTAT<0>) was set
before the transfer was received.
b)
The overflow bit SSPOV (SSPCON<6>) was set
before the transfer was received.
In this case, the SSPSR register value is not loaded
into the SSPBUF, but bit SSPIF (PIR1<3>) is set.
Table 9-2 shows what happens when a data transfer
byte is received, given the status of bits BF and
SSPOV. The shaded cells show the condition where
user software did not properly clear the overflow condi-
tion. Flag bit BF is cleared by reading the SSPBUF
register, while bit SSPOV is cleared through software.
The SCL clock input must have a minimum high and
low for proper operation. The high and low times of the
I2C specification, as well as the requirements of the
SSP module, are shown in timing parameter #100 and
parameter #101.
Read
Write
SSPSR Reg
Match Detect
SSPADD Reg
Start and
Stop bit Detect
SSPBUF Reg
Internal
Data Bus
Addr Match
Set, Reset
S, P bits
(SSPSTAT Reg)
RC3/SCK/SCL
RC4/
Shift
Clock
MSb
SDI/
LSb
SDA
相關PDF資料
PDF描述
PIC16F1934T-E/P 8-BIT, FLASH, 32 MHz, RISC MICROCONTROLLER, PDIP40
PIC16LF1938T-I/SP 8-BIT, FLASH, 32 MHz, RISC MICROCONTROLLER, PDIP28
PIC16F688-IST 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDSO14
PIC18F4450-E/P 8-BIT, FLASH, 48 MHz, MICROCONTROLLER, PDIP40
PIC18F4450T-E/PT 8-BIT, FLASH, 48 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
PIC16CR74T-I/ML 功能描述:IC PIC MCU 4KX14 44QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
PIC16CR74T-I/PT 功能描述:IC PIC MCU 4KX14 44TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
PIC16CR76-I/ML 功能描述:IC PIC MCU 8KX14 28QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
PIC16CR76-I/SO 功能描述:IC PIC MCU 8KX14 28SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
PIC16CR76-I/SP 功能描述:IC PIC MCU 8KX14 28DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*