- 您現在的位置：買賣IC網 > PDF目錄3826 > PIC16F84-04I/SO (Microchip Technology)IC MCU FLASH 1KX14 EE 18SOIC PDF資料下載
參數資料
| 型號： | PIC16F84-04I/SO |
| 廠商： | Microchip Technology |
| 文件頁數： | 16/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU FLASH 1KX14 EE 18SOIC |
| 產品培訓模塊： | Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 42 |
| 系列： | PIC® 16F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 4MHz |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 13 |
| 程序存儲器容量： | 1.75KB（1K x 14） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大小： | 64 x 8 |
| RAM 容量： | 68 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4 V ~ 6 V |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 18-SOIC（0.295"，7.50mm 寬） |
| 包裝： | 管件 |
| 配用： | XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MIL 309-1075-ND - ADAPTER 18-SOIC TO 18-SOIC 309-1011-ND - ADAPTER 18-SOIC TO 18-DIP 309-1010-ND - ADAPTER 18-SOIC TO 18-DIP AC164010-ND - MODULE SKT PROMATEII DIP/SOIC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
PIC16F8X
1998 Microchip Technology Inc.
DS30430C-page 23
5.2
PORTB and TRISB Registers
PORTB is an 8-bit wide bi-directional port. The
corresponding data direction register is TRISB. A ’1’ on
any bit in the TRISB register puts the corresponding
output driver in a hi-impedance mode. A ’0’ on any bit
in the TRISB register puts the contents of the output
latch on the selected pin(s).
Each of the PORTB pins have a weak internal pull-up.
A single control bit can turn on all the pull-ups. This is
done by clearing the RBPU (OPTION_REG<7>) bit.
The weak pull-up is automatically turned off when the
port pin is configured as an output. The pull-ups are
disabled on a Power-on Reset.
Four of PORTB’s pins, RB7:RB4, have an interrupt on
change feature. Only pins configured as inputs can
cause this interrupt to occur (i.e., any RB7:RB4 pin
configured as an output is excluded from the interrupt
on change comparison). The pins value in input mode
are compared with the old value latched on the last
read of PORTB. The “mismatch” outputs of the pins are
OR’ed
together
to
generate
the
RB
port
change interrupt.
FIGURE 5-3:
BLOCK DIAGRAM OF PINS
RB7:RB4
This interrupt can wake the device from SLEEP. The
user, in the interrupt service routine, can clear the
interrupt in the following manner:
a)
Read (or write) PORTB. This will end the mis-
match condition.
b)
Clear flag bit RBIF.
A mismatch condition will continue to set the RBIF bit.
Reading PORTB will end the mismatch condition, and
allow the RBIF bit to be cleared.
This interrupt on mismatch feature, together with
software configurable pull-ups on these four pins allow
easy interface to a key pad and make it possible for
wake-up on key-depression (see AN552 in the
Embedded Control Handbook).
The interrupt on change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt on change
feature. Polling of PORTB is not recommended while
using the interrupt on change feature.
FIGURE 5-4:
BLOCK DIAGRAM OF PINS
RB3:RB0
RBPU(1)
Data Latch
From other
P
VDD
Q
D
CK
Q
D
CK
QD
EN
QD
EN
Data bus
WR Port
WR TRIS
Set RBIF
TRIS Latch
RD TRIS
RD Port
RB7:RB4 pins
weak
pull-up
RD Port
Latch
TTL
Input
Buffer
Note
1: TRISB = ’1’ enables weak pull-up
(if RBPU = ’0’ in the OPTION_REG register).
2: I/O pins have diode protection to VDD and VSS.
I/O
pin(2)
Note 1: For a change on the I/O pin to be
recognized, the pulse width must be at
least TCY (4/fOSC) wide.
RBPU(1)
I/O
pin(2)
Data Latch
P
VDD
Q
D
CK
Q
D
CK
QD
EN
Data bus
WR Port
WR TRIS
RD TRIS
RD Port
weak
pull-up
RD Port
RB0/INT
TTL
Input
Buffer
Schmitt Trigger
Buffer
TRIS Latch
Note
1: TRISB = ’1’ enables weak pull-up
(if RBPU = ’0’ in the OPTION_REG register).
2: I/O pins have diode protection to VDD and VSS.
相關PDF資料 |
PDF描述 |
|---|---|
| DSPIC33FJ64GP802-E/MM | IC DSPIC MCU/DSP 64K 28-QFN |
| PIC18LF4455-I/PT | IC PIC MCU FLASH 12KX16 44TQFP |
| PIC18F4455-I/ML | IC PIC MCU FLASH 12KX16 44QFN |
| PIC24FJ64GB108-I/PT | IC PIC MCU FLASH 80TQFP |
| DSPIC33FJ64MC506A-I/PT | IC DSPIC MCU/DSP 64K 64-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC16F84-10/P | 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 10MHz PDIP18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16F84-10/P | 制造商:Microchip Technology Inc 功能描述:IC 8-BIT FLASH MCU |
| PIC16F84-10/SO | 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 10MHz SOIC18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16F84-10/SO | 制造商:Microchip Technology Inc 功能描述:IC SM 8-BIT FLASH MCU |
| PIC16F84-10I/P | 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 10MHz IndTemp PDIP18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。