參數資料
型號: PIC24HJ256GP610A-I/PT
廠商: Microchip Technology
文件頁數: 12/84頁
文件大?。?/td> 0K
描述: IC MCU 16BIT 256KB FLASH 100TQFP
標準包裝: 119
系列: PIC® 24H
核心處理器: PIC
芯體尺寸: 16-位
速度: 40 MIP
連通性: CAN,I²C,IrDA,LIN,SPI,UART/USART
外圍設備: 欠壓檢測/復位,DMA,POR,PWM,WDT
輸入/輸出數: 85
程序存儲器容量: 256KB(85.5K x 24)
程序存儲器類型: 閃存
RAM 容量: 16K x 8
電壓 - 電源 (Vcc/Vdd): 3 V ~ 3.6 V
數據轉換器: A/D 32x10b/12b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 100-TQFP
包裝: 托盤
dsPIC33F/PIC24H PROGRAMMING SPECIFICATION
DS70152H-page 2
2010 Microchip Technology Inc.
FIGURE 2-2:
CONNECTIONS FOR THE
ON-CHIP REGULATOR
2.2
Program Memory Write/Erase
Requirements
The program Flash memory on the dsPIC33F/PIC24H
has a specific write/erase requirement that must be
adhered to, for proper device operation. The rule is that
any given word in memory must not be written without
first erasing the page in which it is located. Thus, the
easiest way to conform to this rule is to write all the data
in a programming block within one write cycle. The
programming methods specified in this document
comply with this requirement.
2.3
Pins Used During Programming
The pins that are used for programming are listed in
TABLE 2-1:
PINS USED DURING PROGRAMMING
Note 1: These are typical operating voltages. Refer
operating ranges of VDD and VCAP.
2: It is important for the low-ESR capacitor to
be placed as close as possible to the VCAP
pin.
VDD
VCAP
VSS
dsPIC33F/PIC24H
CEFC
3.3V
Note:
A program memory word can be
programmed twice before an erase, but
only if (a) the same data is used in both
program operations or (b) bits containing
‘1’ are set to ‘0’ but no ‘0’ is set to ‘1’.
Note:
Refer to the specific device data sheet for
complete pin diagrams of the dsPIC33F/
PIC24H devices.
Pin Name
During Programming
Pin Name
Pin Type
Pin Description
MCLR
P
Programming Enable
VDD and AVDD(1)
VDD
P
Power Supply
VSS and AVSS(1)
VSS
P
Ground
VCAP
P
CPU Logic Filter Capacitor Connection
PGEC1
I
Primary Programming Pin Pair: Serial Clock
PGED1
I/O
Primary Programming Pin Pair: Serial Data
PGEC2
I
Secondary Programming Pin Pair: Serial Clock
PGED2
I/O
Secondary Programming Pin Pair: Serial Data
PGEC3
I
Tertiary Programming Pin Pair: Serial Clock
PGED3
I/O
Tertiary Programming Pin Pair: Serial Data
Legend: I = Input
O = Output
P = Power
Note 1: All power supply and ground pins must be connected, including analog supplies (AVDD) and ground
(AVSS).
相關PDF資料
PDF描述
PIC24HJ256GP610-I/PT IC PIC MCU FLASH 128KX16 100TQFP
PIC32MX360F256L-80I/BG IC MCU 32BIT 256KB FLASH 121XBGA
608489030001049 CONN RECEPT COAX FOR 8074/8075
608489050009049 CONN CONTACT FOR 8483/8484 PLUGS
PIC24FJ128GB210-I/BG MCU PIC 16BIT FLASH USB 121BGA
相關代理商/技術參數
參數描述
PIC24HJ256GP610AT-I/PF 功能描述:16位微控制器 - MCU 16 Bit MCU 40MIPS 256KB FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PIC24HJ256GP610AT-I/PT 功能描述:16位微控制器 - MCU 16 Bit MCU 40MIPS 256KB FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PIC24HJ256GP610I/PF 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Microcontrollers
PIC24HJ256GP610-I/PF 功能描述:16位微控制器 - MCU 16 Bit MCU 100LD 40 MIPS 256KB Flash RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PIC24HJ256GP610I/PF-ES 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Microcontrollers