- 您現在的位置：買賣IC網 > PDF目錄69061 > PM6681ATR (STMICROELECTRONICS) 0.4 A DUAL SWITCHING CONTROLLER, QCC32 PDF資料下載
參數資料
| 型號： | PM6681ATR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.4 A DUAL SWITCHING CONTROLLER, QCC32 |
| 封裝： | 5 X 5 MM, 1 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, VFQFPN-32 |
| 文件頁數： | 37/47頁 |
| 文件大小： | 2762K |
| 代理商： | PM6681ATR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
Layout guidelines
PM6681A
42/47
10
Layout guidelines
The layout is very important in terms of efficiency, stability and noise of the system. It is
possible to refer to the PM6681A demonstration board for a complete layout example.
For good PC board layout follows these guidelines:
●
Place on the top side all the power components (inductors, input and output capacitors,
MOSFETs and diodes). Refer them to a power ground plan, PGND. If possible, reserve
a layer to PGND plan. The PGND plan is the same for both the switching sections.
●
AC current paths layout is very critical (see Figure 44). The first priority is to minimize
their length. Trace the LS MOSFET connection to PGND plan (with or without current
sense resistor RSENSE) as short as possible. Place the synchronous diode D near the
LS MOSFET. Connect the LS MOSFET drain to the switching node with a short trace.
●
Place input capacitors near HS MOSFET drain. It is recommended to use the same
input voltage plan for both the switching sections, in order to put together all input
capacitors.
●
Place all the sensitive analog signals (feedbacks, voltage reference and current sense
paths) on the bottom side of the board or in an inner layer. Isolate them from the power
top side with a signal ground layer, SGND. Connect the SGND and PGND plans only in
one point (a multiple via connection is preferable to a 0 ohm resistor connection) near
the PGND device pin. Place the device on the top or on the bottom size and connect
the exposed pad and the SGND pins to the SGND plan (see Figure 44).
Figure 44.
Current paths, ground connection and driver traces layout
相關PDF資料 |
PDF描述 |
|---|---|
| PMA4118HSF/C | 1-OUTPUT 18 W DC-DC REG PWR SUPPLY MODULE |
| PMA4118LSF/B | 1-OUTPUT 14.4 W DC-DC REG PWR SUPPLY MODULE |
| PMA4218GSF/B | 1-OUTPUT 21.6 W DC-DC REG PWR SUPPLY MODULE |
| PMA4118LSF/C | 1-OUTPUT 14.4 W DC-DC REG PWR SUPPLY MODULE |
| PMA4118HSF/B | 1-OUTPUT 18 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PM6685 | 功能描述:DC/DC 開關控制器 Dual Step Down Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| PM6685_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Dual step-down main supply controller with auxilary voltages for notebook system power |
| PM6685TR | 功能描述:DC/DC 開關控制器 Monolithic VR RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| PM6686 | 制造商:STMicroelectronics 功能描述: |
| PM6686TR | 功能描述:DC/DC 開關控制器 Step-down Controller w/adj. voltages-dual RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。