- 您現在的位置：買賣IC網 > PDF目錄368150 > PSD412A1-20UI -30V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a SMD-0.5 package; A IRHNJ597Z30 with Standard Packaging PDF資料下載
參數資料
| 型號： | PSD412A1-20UI |
| 英文描述： | -30V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a SMD-0.5 package; A IRHNJ597Z30 with Standard Packaging |
| 中文描述： | 現場可編程外圍 |
| 文件頁數： | 79/123頁 |
| 文件大?。?/td> | 657K |
| 代理商： | PSD412A1-20UI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁當前第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
Port Configuration
Reset
Stand-by Mode
Port I/O
Input
Unchanged
ZPLD Output
Active
Depend on Inputs to the ZPLD
Address Out
Tri-stated
Not Defined
Data Port
Tri-stated
Tri-stated
Peripheral I/O
Tri-stated
Tri-stated
PSD4XX Famly
76
Register Name
Device
Reset State
Control
Port A, B, C, D, E
Set to “0”
(Address Out Mode)
Data Out
(data or address)
Port A, B, C, D, E
Set to “0”
Direction
Port A, B, C, D, E
Set to “0” – Input Mode
Open Drain
Port C, D
Set to “0” – CMOS Outputs
Page Register
Page Logic
Set to “0”
PMMR0, PMMR1
Power Management Unit
Set to “0”
VM
Volatile Memory
Set to “0”
System
Configuration
(cont.)
Table 24. Registers Reset Values
Table 25. I/OPin Status During Reset and Standby Mode
12.1 Reset Input
The reset input to the PSD4XX (RESET) is an active low signal which resets some of the
internal devices and configuration registers. The Timing Diagram in the AC/DC
characterization section shows the reset signal timing requirement. The active low range
has a minimum T1 duration. After the rising edge of RESET, the PSD4XX remains in
reset during T2 range. (See Figure 48). The PSD4XX must be reset at power up before it
can be used.
12.2 ZPLDand Memory During Reset
While the Reset Input is active, the ZPLD generates outputs as defined in the PSDabel
equations. The EPROM and SRAM blocks respond to the microcontroller bus cycle during
reset, but the data is not guaranteed.
12.3 Register Values During and After Reset
Table 24 summarizes the status of the volatile register values during and after reset.
The default values of the volatile registers are “0” after reset.
12.4 ZPLDMacrocell Initialization
The D flip flops in the macrocells in the GPLD can be cleared by:
J
A product term (.RE) defined by the user in PSDabel, or
J
The MACRO-RST (Reset) input, enabled and defined in PSDabel.
相關PDF資料 |
PDF描述 |
|---|---|
| PSD412A1-70J | -100V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a TO-205AF package; A IRHF597130 with Standard Packaging |
| PSD412A1-70U | -30V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a Low-Ohmic TO-254AA package; A IRHMS597Z60 with Standard Packaging |
| PSD412A1-90J | Field-Programmable Peripheral |
| PSD412A1-90U | 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-1 package; A IRHN7230 with Standard Packaging |
| PSD412A2 | 100V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a 18-pin LCC package; Similar to IRHE7130 with optional Total Dose Rating of 300kRads |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD412A1-70J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD412A1-70U | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD412A1-90J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD412A1-90U | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD412A1-A-20JI | 制造商:WSI 功能描述:PERIPHERAL IC |
發布緊急采購，3分鐘左右您將得到回復。