參數資料
型號： PSD413A2-12LI
英文描述： Field-Programmable Peripheral
中文描述： 現場可編程外圍
文件頁數： 73/123頁
文件大?。?/td> 657K
代理商： PSD413A2-12LI
PSD4XX Famly
70
9.5.2 Oher Power Saving Options
The PSD4XX provides additional power saving options. These options, except the SRAM
Standby Mode, can be enabled/disabled by setting up the corresponding bit in the PMMR.
J
EPROM
The EPROM power consumption in the PSD is controlled by bit 3 in the
PMMR0 – EPROM CMiser. Upon reset the CMiser bit is OFF. This will cause the
EPROM to be ON at all times as long as CSI is enabled (low). The reason this mode is
provided is to reduce the access time of the EPROM by 10 ns relative to the low power
condition when CMiser is ON. If CSI is disabled (high) the EPROM will be deselected
and will enter standby mode (OFF) overriding the state of the CMiser.
If CMiser is set (ON) then the EPROM will enter the standby mode when not selected.
This condition can take place when CSI is high or when CSI is low and the EPROM is
not accessed. For example, if the MCU is accessing the SRAM, the EPROM will be
deselected and will be in low power mode.
An additional advantage of the CMiser is achieved when the PSD is configured in the
by 8 mode (8 bit data bus). In this case an additional power savings is achieved in the
EPROM (and also in the SRAM) by turning off 1/2 of the array even when the EPROM
is accessed (the array is divided internally into odd and even arrays).
The power consumption for the different EPROM modes is given in the DC
Characteristics table under I
CC
(DC) EPROM Adder.
J
SRAM Standby Mode
The SRAM has a dedicated supply voltage V
STBY
that can be used to connect a battery.
When V
CC
becomes lower than V
STBY
–0.6 then the PSD will automatically connect
the V
STBY
as a power source to the SRAM. The SRAM Standby Current (I
STBY
) is
typically 0.5 μA.
SRAM data retention voltage V
DF
is 2 V minimum.
J
Zero Power ZPLD
ZPLD power/speed is controlled by the ZPLD_Turbo bit (bit 4) in the PMMR0.
After reset the ZPLD is in Turbo mode and runs at full power and speed. By setting the
bit to “1”, the Turbo mode is disabled and the ZPLD is consuming Zero Power current if
the inputs are not switching for an extended time of 70 ns. The propagation delay time
will be increased by 10ns after the Turbo bit is set to “1” (turned off) if the inputs change
at a frequency of less than 15 MHz.
The PSD4XX
Architecture
(cont.)
相關PDF資料
PDF描述
PSD413A2-12U 150V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-0.5 package also available with Total Dose Rating of 300kRads; A IRHNJ67134 with Standard Packaging
PSD413A2-12UI -200V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a TO-257AA package; A IRHY9230CM with Standard Packaging
PSD413A2-15J Field-Programmable Peripheral
PSD413A2-15JI 100V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-3 package; Similar to IRHNB7160 with optional Total Dose Rating of 300kRads
PSD413A2-15LI 100V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-3 package; A IRHNB7160 with Standard Packaging
相關代理商/技術參數
參數描述
PSD413A2-C-70L 制造商:WSI 功能描述:
PSD4-16 制造商:Tamura Corporation of America 功能描述:
PSD4-20 制造商:MICROTRAN 功能描述:POWER TRANSFORMER, 6 VA
PSD4235G2-70U 功能描述:SPLD - 簡單可編程邏輯器件 5.0V 4M 70ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池?cái)?shù)量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD4235G2-90U 功能描述:CPLD - 復雜可編程邏輯器件 5.0V 4M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*