參數資料
型號： PSD4235G3-A-15JI
廠商： 意法半導體
英文描述： CAP 0.68UF 20V 10% TANT SMD-3216-18 TR-13-PL GOLD
中文描述： Flash在系統可編程外設的16位微控制器
文件頁數： 64/89頁
文件大?。?/td> 703K
代理商： PSD4235G3-A-15JI
PSD4235G2
64/89
JTAG Extensions.
TSTAT and TERR are two
JTAG extension signals enabled by a JTAG com-
mand received over the four standard JTAG pins
(TMS, TCK, TDI, and TDO). They are used to
speed Program and Erase cycles by indicating
status on PSD pins instead of having to scan the
status out serially using the standard JTAG chan-
nel. See Application Note AN1153.
TERR indicates if an error has occurred when
erasing a sector or programming in Flash memory.
This signal goes Low (active) when an Error con-
dition occurs, and stays Low until a specific JTAG
command is executed or a Reset (RESET) pulse
is received after an “ISC_DISABLE” command.
TSTAT behaves the same as Ready/Busy (PE4)
described in the section entitled “Ready/Busy
(PE4)”, on page 21. TSTAT is High when the
PSD4235G2 device is in Read mode (primary
Flash memory and secondary Flash memory con-
tents can be read). TSTAT is Low when Flash
memory Program or Erase cycles are in progress,
and also when data is being written to the second-
ary Flash memory .
TSTAT and TERR can be configured as open-
drain type signals with a JTAG command.
Note: The state of Reset (Reset) does not interrupt
(or prevent) JTAG operations if the JTAG signals
are dedicated by an NVM Configuration bit (via
PSDsoft Express). However, Reset (Reset) pre-
vents or interrupts JTAG operations if the JTAG
Enable Register (as shown in Table 21) is used to
enable the JTAG signals.
Security and Flash memory Protection.
When
the security bit is set, the device cannot be read on
a Device Programmer or through the JTAG Port.
When using the JTAG Port, only a Full Chip Erase
command is allowed.
All other Program, Erase and Verify commands
are blocked. Full Chip Erase returns the device to
a non-secured blank state. The Security Bit can be
set in PSDsoft Express.
All primary Flash memory and secondary Flash
memory sectors can individually be sector protect-
ed against erasure. The sector protect bits can be
set in PSDsoft Express.
INITIAL DELIVERY STATE
When delivered from ST, the PSD device has all
bits in the memory and PLDs set to 1. The PSD
Configuration Register bits are set to 0. The code,
configuration, and PLD logic are loaded using the
programming procedure. Information for program-
ming the device is available directly from ST.
Please contact your local sales representative.
PE4
TSTAT
Status
PE5
TERR
Error Flag
Port E Pin
JTAG Signals
Description
相關PDF資料
PDF描述
PSD4235G3-A-15M CAP 0.68UF 20V 10% TANT SMD-3216-18 TR-13-PL SN/PB5%
PSD4235G3-A-15MI CAP 0.68UF 20V 10% TANT SMD-3216-18 TR-13-PL SN100%
PSD4235G3-A-15U CAP 0.68UF 20V 10% TANT SMD-3216-18 TR-13-PL SN100%
PSD4235G3-A-15UI Flash In-System-Programmable Peripherals for 16-Bit MCUs
PSD4235G3-B-15J Flash In-System Programmable ISP Peripherals For 16-bit MCUs 5V Supply
相關代理商/技術參數
參數描述
PSD4256G6V-10UI 功能描述:CPLD - 復雜可編程邏輯器件 3.3V 8M 100ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD4-36 制造商:Tamura Corporation of America 功能描述:
PSD-45 制造商:MEANWELL 制造商全稱:Mean Well Enterprises Co., Ltd. 功能描述:45W DC-DC Single Output Switching Power Supply
PSD-45_11 制造商:MEANWELL 制造商全稱:Mean Well Enterprises Co., Ltd. 功能描述:45W DC-DC Single Output Switching Power Supply
PSD-45A-05 功能描述:線性和開關式電源 30W 5Vout 6A Input 9.2-18VDC RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*