參數資料
型號： PSD511B1
英文描述： Field Programmable Microcontroller Peripherals(可編程邏輯，16K位SRAM,40個可編程I/O,通用PLD有61個輸入)
中文描述： 現場可編程微控制器外圍設備（可編程邏輯，16K的位的SRAM，40余個可編程輸入/輸出，通用PLD的有61個輸入）
文件頁數： 54/130頁
文件大小： 704K
代理商： PSD511B1
PSD5XX Famly
6-54
Peripheral I/O
The Peripheral I/O Mode is one of the operating modes of Port A. In this mode, Port A
is connected to the data bus of peripheral devices. Port A is enabled only when the
microcontroller is accessing the devices, otherwise the Port is tri-stated. This feature
enables the microcontroller to access external devices without requiring buffers and
decoders. Figure 27 shows the structure of Port A in the Peripheral I/O Mode.
The memory address space occupied by the devices are defined by two signals: PSEL0
and PSEL1. The signals are direct outputs from the DPLD. Whenever any of the signals is
active, the Port A driver is enabled, and the direction of the data flow is determined by the
RD/WR signals.
The Peripheral I/O Mode and the peripheral select signals are configured and defined in the
PSDsoft Software (see the section on I/O Port for configurations). The PIO bit in the VM
Register (see Table 16) also needs to be set to “1” by the user to initialize the Peripheral I/O
Mode.
The Peripheral I/O mode can be used, for example, in DMA applications where the
microcontroller does not support DMA operations, such as tri-stating the address/data bus.
Figure 28 shows a block diagram of a microcontroller and PSD5XX based design that
makes use of this mode. In this application, the microcontroller has a multiplexed bus which
is connected to the ADIO port. The C and D ports connect to the peripheral address bus
and are both configured in Address Out Mode. Port A is configured in the Peripheral I/O
mode and is connected to the peripheral data bus. Port B and E are used to generate
control signals.
During normal activity, the microcontroller has access to any peripheral (memory or I/O
device) through the PSD5XX device. When there is a DMA request, the microcontroller
tri-states the address bus on Port C and D by writing a “0” to the port Direction Registers.
The DMA controller then takes over the data and address buses after receiving
acknowledgement from the microcontroller.
Figure 27. Port A In Peripheral I/OMode
RD
PSEL0
PSEL1
D0 – D7
WR
PA0 – PA7
Peripheral I/O
相關PDF資料
PDF描述
PSD502B1 Field Programmable Microcontroller Peripherals(可編程邏輯，16K位SRAM,40個可編程I/O,通用PLD有61個輸入)
PSD503B1 Field Programmable Microcontroller Peripherals(可編程邏輯，16K位SRAM,40個可編程I/O,通用PLD有61個輸入)
PSD502B1-12U 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a TO-204AE package; Similar to IRH7250 with optional Total Dose Rating of 1000kRads
PSD502B1-12UI 250V 100kRad Hi-Rel Single N-Channel SEE Hardened MOSFET in a TO-254AA package; A IRHM57264SE with Standard Packaging
PSD502B1-15J 600V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a TO-257AA package. Also available in Radiation Levels up to 300KRad.; Similar to IRHY67C30CM with Optional Total Dose Rating of 300kRads
相關代理商/技術參數
參數描述
PSD511B1-12J 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD511B1-12JI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD511B1-12LI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD511B1-12U 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD511B1-12UI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*