參數資料
型號： PSD813F1-A-90JI
廠商： 意法半導體
英文描述： Flash In-System Programmable ISP Peripherals For 8-bit MCUs
中文描述： Flash在系統可編程ISP的外設的8位微控制器
文件頁數： 28/110頁
文件大?。?/td> 1685K
代理商： PSD813F1-A-90JI
PSD813F1
28/110
Data Toggle
Checking the Data Toggle bit on DQ6 is a method
of determining whether a Program or Erase in-
struction is in progress or has completed. Figure
10
shows the Data Toggle algorithm.
When the MCU issues a programming instruction,
the embedded algorithm within the PSD begins.
The MCU then reads the location of the byte to be
programmed in Flash to check status. Data bit
DQ6 of this location will toggle each time the MCU
reads this location until the embedded algorithm is
complete. The MCU continues to read this loca-
tion, checking DQ6 and monitoring the Error bit on
DQ5. When DQ6 stops toggling (two consecutive
reads yield the same value), and the Error bit on
DQ5 remains
‘
0
’
, then the embedded algorithm is
complete. If the Error bit on DQ5 is
‘
1
’
, the MCU
should test DQ6 again, since DQ6 may have
changed simultaneously with DQ5 (see Figure
10
).
The Error bit at DQ5 will be set if either an internal
timeout occurred while the embedded algorithm
attempted to program the byte, or if the MCU at-
tempted to program a
‘
1
’
to a bit that was not
erased (not erased is logic
‘
0
’
).
It is suggested (as with all Flash memories) to read
the location again after the embedded program-
ming algorithm has completed to compare the byte
that was written to Flash with the byte that was in-
tended to be written.
When using the Data Toggle method after an
erase instruction, Figure
10
still applies. DQ6 will
toggle until the erase operation is complete. A
‘
1
’
on DQ5 will indicate a timeout failure of the erase
operation, a
‘
0
’
indicates no error. The MCU can
read any location within the sector being erased to
get DQ6 and DQ5.
PSDsoft Express will generate ANSI C code func-
tions which implement these Data Toggling algo-
rithms.
Figure 10. Data Toggle Flowchart
READ
DQ5 & DQ6
START
READ DQ6
FAIL
PASS
AI01370B
D=
TOGGLE
NO
NO
YES
YES
DQ5
= 1
NO
YES
D=
TOGGLE
相關PDF資料
PDF描述
PSD813F1A-90MI Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD813F1A-90MT Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD813F1V Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F2V-15 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD813F2V-20 Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
相關代理商/技術參數
參數描述
PSD813F1A-90JI 功能描述:SPLD - 簡單可編程邏輯器件 5.0V 1M 90ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD813F1A-90JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD813F1-A-90M 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F1A-90M 功能描述:CPLD - 復雜可編程邏輯器件 5.0V 1M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD813F1-A-90MI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*