參數資料
型號： PSD813F1-A
廠商： 意法半導體
元件分類： 基準電壓源/電流源
英文描述： Enhanced High Power Factor Preregulator 16-PDIP 0 to 70
中文描述： Flash在系統可編程ISP的外設的8位微控制器
文件頁數： 21/110頁
文件大?。?/td> 1685K
代理商： PSD813F1-A
21/110
PSD813F1
INSTRUCTIONS
An instruction is defined as a sequence of specific
operations. Each received byte is sequentially de-
coded by the PSD and not executed as a standard
write operation. The instruction is executed when
the correct number of bytes are properly received
and the time between two consecutive bytes is
shorter than the time-out value. Some instructions
are structured to include READ operations after
the initial WRITE operations.
The sequencing of any instruction must be fol-
lowed exactly. Any invalid combination of instruc-
tion bytes or time-out between two consecutive
bytes while addressing Flash memory will reset
the device logic into READ mode (Flash memory
reads like a ROM device). An invalid combination
or time-out while addressing the EEPROM block
will cause the offending byte to be interpreted as a
single operation.
The PSD supports these instructions (see
Table
8., page 20
):
Flash memory:
Erase memory by chip or sector
Suspend or resume sector erase
Program a Byte
Reset to READ mode
Read Flash Identifier value
Read Sector Protection Status
EEPROM:
Write data to OTP Row
Read data from OTP Row
Power down memory
Enable Software Data Protect (SDP)
Disable SDP
Return from read OTP Row read mode or
power down mode.
I
I
I
I
I
I
I
I
I
I
I
I
These
8., page 20
. For efficient decoding of the instruc-
tions, the first two bytes of an instruction are the
coded cycles and are followed by a command byte
or confirmation byte. The coded cycles consist of
writing the data AAh to address X555h during the
first cycle and data 55h to address XAAAh during
the second cycle. Address lines A15-A12 are don
’
t
cares during the instruction WRITE cycles. How-
ever, the appropriate sector select signal (FSi or
EESi) must be selected.
Power-down Instruction and Power-up Mode
EEPROM Power Down Instruction.
The
PROM can enter power down mode with the help
of the EEPROM power down instruction (see
Ta-
ble 8., page 20
). Once the EEPROM power down
instruction is decoded, the EEPROM memory can-
not be accessed unless a Return instruction (also
in
Table 8., page 20
) is decoded. Alternately, this
power down mode will automatically occur when
the APD circuit is triggered (see section entitled
Automatic Power-down (APD) Unit and Power-
down Mode, page 65
). Therefore, this instruction
is not required if the APD circuit is used.
Power-up Mode.
The PSD internal logic is reset
upon power-up to the READ mode. Any write op-
eration to the EEPROM is inhibited during the first
5ms following power-up. The FSi and EESi select
signals, along with the write strobe signal, must be
in the false state during power-up for maximum se-
curity of the data contents and to remove the pos-
sibility of a byte being written on the first edge of a
write strobe signal. Any write cycle initiation is
locked when V
CC
is below V
LKO
.
instructions
are
detailed
in
Table
EE-
相關PDF資料
PDF描述
PSD813F1-A-12JI Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F1-A-12MI Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F1-A-90J Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F1-A-90JI Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F1A-90MI Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
相關代理商/技術參數
參數描述
PSD813F1A-12J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD813F1-A-12JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F1A-12JI 功能描述:CPLD - 復雜可編程邏輯器件 5.0V 1M 120ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD813F1A-12JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD813F1A-12M 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*