參數資料
型號: PTV03020WAH
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源模塊
英文描述: 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
封裝: SIP-12
文件頁數: 15/19頁
文件大?。?/td> 434K
代理商: PTV03020WAH
www.ti.com
DEVICE INFORMATION
PIN 1
PIN 5
PIN 12
SLTS243A – FEBRUARY 2005 – REVISED OCTOBER 2007
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
NAME
NO.
VI
5, 6
The positive input voltage power node to the module, which is referenced to common GND.
VO
3, 4
The regulated positive power output with respect to the GND node.
This is the common ground connection for the VI and VO power connections. It is also the 0-Vdc reference for the
GND
1, 2, 10, 11
control inputs.
The Inhibit pin is an open-collector/drain, active-low input that is referenced to GND. Applying a low-level ground
signal to this input disables the module's output and turns off the output voltage. When the Inhibit control is active,
Inhibit
12
the input current drawn by the regulator is significantly reduced. If the inhibit feature is not used, the control pin
should be left open-circuit. The module then produces an output voltage whenever a valid input source is applied.
A 1% resistor must be connected directly between this pin and GND (pin 1 or 2) to set the output voltage of the
module higher than its lowest value. The temperature stability of the resistor should be 100 ppm/
°C (or better).
The set-point range is 0.8 V to 3.6 V. The resistor value can be calculated using a formula. If this input is left
Vo Adjust
8
open-circuit, the output voltage defaults to its lowest value. For further information, consult the related application
note.
The specification table gives the standard resistor values for a number of common output voltages.
The sense input allows the regulation circuit to compensate for voltage drop between the module and the load. For
Vo Sense
7
optimal voltage accuracy Vo Sense should be connected to VO. It can also be left disconnected.
This is an analog control input that enables the output voltage to follow an external voltage. This pin becomes
active typically 20 ms after the input voltage has been applied, and allows direct control of the output voltage from
0 V up to the nominal set-point voltage. Within this range, the output follows the voltage at the Track pin on a
volt-for-volt basis. When the control voltage is raised above this range, the module regulates at its set-point
Track
9
voltage. The feature allows the output voltage to rise simultaneously with other modules powered from the same
input bus. If unused, this input should be connected to VI.
NOTE: Due to the undervoltage lockout feature, the output of the module cannot follow its own input voltage
during power up. Consult the related Application Information for further guidance.
Front View of Module
Figure 5. Pin Terminal Locations
Copyright 2005–2007, Texas Instruments Incorporated
5
Product Folder Link(s) :PTV03020W
相關PDF資料
PDF描述
PTV05010WAH 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTV08T250WAH 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTV08T250WAD 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTV12010WAD 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTV12010WAH 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
PTV05010 制造商:ARTESYN 制造商全稱:Artesyn Technologies 功能描述:DC-DC CONVERTERS POLA Non-isolated
PTV05010W 制造商:TI 制造商全稱:Texas Instruments 功能描述:8-A, 5-V INPUT NONISOLATED WIDE-OUTPUT ADJUST SIP MODULE
PTV05010WAD 功能描述:DC/DC轉換器 28.8W 0.8-3.6V 8A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTV05010WAH 功能描述:DC/DC轉換器 8A 5V-In Wide-Out Adj SIP Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTV05020 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC-DC CONVERTERS